Ronseal Direct To Metal Paint - Rural Green - Gloss
Not Available
Not Available
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later or explore other options below.
Product Information
Full details
This guide is for DIYers and professionals looking for a durable, long-lasting paint finish on metal surfaces with minimal preparation. The key benefit is its ability to be applied directly to rust without a primer, offering up to 15 years of protection. A caveat to consider is that multiple coats are recommended for optimal durability, especially on rusty surfaces.
All features
| Colour | Green |
|---|---|
| Brand | Ronseal |
Extended Product Information
FAQs
Do I really need to use a primer with this paint?
No, the key benefit of Ronseal Direct to Metal Paint is that it can be applied directly to rust and bare metal without the need for a separate primer.
How many coats should I apply?
A minimum of two coats is recommended for good coverage and protection. For ultimate durability, especially on rusty metal, three coats are advised.
How long does it take to dry?
The paint is touch dry in 30 minutes and showerproof in the same timeframe. Allow 2 to 4 hours between coats.
What surfaces can I use this paint on?
It is suitable for use on bare metal, previously painted metal, wood, cast iron, and aluminium.
How should I clean my brushes after use?
Clean brushes, rollers, and equipment immediately after use with warm, soapy water.
Can I use this paint on galvanized metal?
While it is designed for bare metal and previously painted surfaces, it's always best to test on a small, inconspicuous area first or consult the manufacturer's guidelines for specific advice on galvanized surfaces.
What is the expected lifespan of the protection?
The paint provides up to 15 years of protection when applied correctly with the recommended number of coats.
Troubleshooting
Paint not adhering well
Ensure the surface was properly prepared (clean, dry, and free from grease). If painting over existing paint, ensure it was adequately abraded. For bare metal, ensure loose rust was removed.
Uneven finish or brush marks
Ensure the paint is stirred thoroughly. Apply thin, even coats rather than one thick coat. Use a good quality brush or roller. If spraying, ensure the correct dilution and pressure are used.
Paint remains tacky after application
This can occur if applied too thickly or in humid/cold conditions. Allow more time for drying in a well-ventilated area. Avoid applying additional coats until the previous one is touch dry.
Rust showing through after painting
This indicates insufficient preparation or coating. For heavily rusted areas, more thorough rust removal and an additional coat (or two) are recommended.
Pros and Cons
Pros
- Saves time and effort due to direct-to-rust application and minimal prep.
- Offers extended protection for up to 15 years.
- Suitable for a wide range of metal and wood surfaces.
- Quick drying and showerproof features allow for faster project completion.
- Low odour makes application more comfortable.
Cons
- Multiple coats are recommended for maximum durability, increasing application time and paint usage.
- Requires careful surface preparation if paint is flaking.
- Not suitable for use on plastics.
- Disposal of leftover paint must be managed responsibly.
Setup, Compatibility & Care
Preparation:
- Bare Metal: Remove loose rust and paint using a wire brush or 120-grit sandpaper. Wipe the surface with a damp cloth and allow it to dry.
- Previously Painted Metal: If the existing paint is in good condition, lightly abrade the surface with 240-grit sandpaper. If the paint is flaking, remove it using sandpaper or a wire brush and wipe clean and dry.
Application:
- Stir the paint thoroughly before use.
- Apply using a good quality paintbrush or roller.
- For spraying, dilute the paint with approximately 10% water.
- Apply a minimum of two coats for adequate coverage and protection. For rusty metal, three coats are recommended for ultimate durability.
- Allow 2 to 4 hours between coats.
Compatibility:
- Suitable for use on bare metal, previously painted metal, wood, cast iron, and aluminium.
Care & Cleaning:
- Clean brushes, rollers, and equipment immediately after use with warm soapy water.
- Do not empty leftover paint into drains or watercourses. Contact your local authority for correct disposal procedures.
- Store paint in a cool, dry place away from direct sunlight.