Ronseal Direct To Metal Paint - Gloss - Copper - 250Ml
Not Available
Not Available
Not Available
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later or explore other options below.
Product Information
Full details
Ronseal Direct to Metal Paint is designed for DIY enthusiasts and professionals seeking a quick and durable solution for painting metal surfaces. Its key benefit is the ability to apply directly to rust without a primer, saving significant preparation time and offering 15-year protection. A potential caveat is that while water-based, it requires specific application directions for optimal longevity.
All features
| Colour | Copper |
|---|---|
| Model Part Number | 39405 |
| Brand | Ronseal |
Extended Product Information
FAQs
Do I really need to use a primer?
No, Ronseal Direct to Metal Paint is specifically formulated to be applied directly to rust and metal surfaces without the need for a primer, saving you time and effort.
How long does the protection last?
When applied correctly according to the instructions on the tin, the paint offers 15 years of protection.
What surfaces can I use this paint on?
It is suitable for use on cast iron, aluminium, steel, and wood. It can be applied to bare metal, primed metal, or previously painted surfaces.
How long does it take to dry?
The paint is showerproof in 30 minutes. Allow at least 4 hours between coats, but refer to the product tin for precise recoating times to ensure maximum protection.
Can I use this paint outdoors?
Yes, it is designed for both interior and exterior metal surfaces, providing durable protection against weather conditions.
Is it suitable for heavily rusted items?
Yes, it can be applied directly to rust. However, it is important to remove any loose or flaking rust first for best adhesion and protection.
How do I clean my brushes after use?
As this is a water-based paint, brushes and equipment can be cleaned easily with soap and water immediately after use.
Troubleshooting
Paint is not adhering well
Ensure the surface was properly cleaned and free of grease. Check that previous coats were adequately dry and that the correct application method was followed. Lightly abrading the surface before application can improve adhesion.
Paint finish appears uneven
Stir the paint thoroughly before and during use. Apply thin, even coats. Avoid over-brushing or over-rolling. Ensure consistent application technique across the surface.
Rust is bleeding through the paint
Ensure all loose rust was removed during preparation. Apply additional thin coats of the paint, allowing adequate drying time between each. For severe rust, specific rust-inhibiting treatments may be necessary prior to painting.
Paint is too thick or too thin
Stir the paint thoroughly. If the paint is too thick, check storage conditions; avoid extreme temperatures. This paint is water-based and should not require thinning, but if absolutely necessary and permitted by instructions, a very small amount of water can be added cautiously. Refer to the product tin for specific guidance.
Pros and Cons
Pros
- Saves time and effort by eliminating primer requirements.
- Offers long-lasting protection against rust and corrosion.
- Low odour formula makes it more pleasant to use indoors or in confined spaces.
- Water-based nature allows for easier cleanup with water.
- Quick drying time speeds up the painting process.
- Suitable for a variety of metal and even wood surfaces.
Cons
- Requires careful adherence to application instructions for the full 15-year protection.
- Performance on heavily corroded or unsound surfaces may vary.
- Water-based paints can sometimes have a shorter shelf-life than solvent-based paints.
- Colour accuracy may vary slightly between batches or finishes.
- Not suitable for immersion in water or constant heavy condensation.
Setup, Compatibility & Care
Preparation:
- Ensure the metal surface is clean, dry, and free from grease or contaminants.
- Remove any loose rust or flaking paint with a wire brush or scraper.
- For best results, lightly abrade the surface if previously painted or very smooth.
Application:
- Stir the paint thoroughly before use.
- Apply a thin, even coat using a brush or roller designed for water-based paints.
- Allow a minimum of 4 hours between coats for optimal drying and adhesion. For full 15-year protection, follow the specific recoating times and number of coats as detailed on the product packaging.
Compatibility:
- Suitable for bare metal, primed metal, and previously painted surfaces (in good condition).
- Compatible with cast iron, aluminium, and steel.
- Can also be applied to wood.
- Not recommended for galvanised steel without appropriate pre-treatment or for surfaces that will be submerged in water.
Care:
- Clean brushes and equipment immediately after use with water.
- Store the paint in a cool, dry place, away from direct sunlight and frost.
- Ensure the lid is tightly sealed to maintain paint quality.