Plasti Dip Blaze Spray Aerosol - Rubber Paint - Fluorescent / Neon Colours - Green
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later or explore other options below.
Product Information
Full details
This guide is for DIY enthusiasts and hobbyists looking to add a vibrant, temporary color finish to various surfaces. The Plasti Dip Blaze Spray Aerosol in Green offers a unique fluorescent, peelable rubber coating for customization projects. A key caveat is that for optimal brightness and performance, applying Blaze colors over a base coat of regular Plasti Dip White is recommended.
All features
| Colour | Green |
|---|---|
| Brand | Plasti Dip |
Extended Product Information
FAQs
How do I prepare the surface before applying Plasti Dip Blaze?
The surface must be clean, dry, and free from grease, oil, and dirt. For best results with Blaze colors, apply a base coat of regular Plasti Dip White first.
Can I apply Plasti Dip Blaze directly over existing paint?
Yes, but for optimal color performance and easier removal, it's recommended to apply it over a base coat of regular Plasti Dip (preferably white for Blaze colors) or ensure the existing paint is well-adhered and clean.
How many coats of Plasti Dip Blaze Green should I apply?
It is recommended to apply 4-6 thin, even coats for best results, with adequate drying time between each coat.
How long does Plasti Dip Blaze Green last?
The longevity depends on the application, environmental conditions, and exposure to wear and tear. It is designed to be a temporary coating and can last from several months to over a year with proper care.
Can Plasti Dip Blaze be used on car exteriors?
Yes, it can be used on car parts like wheels, trim, and grilles. For full vehicle application, professional spraying equipment and techniques are often recommended for a flawless finish.
Is Plasti Dip Blaze Green safe for use on indirect food contact surfaces?
Plasti Dip is not intended for direct or indirect food contact and should not be applied to surfaces that will come into contact with food or beverages.
How do I remove Plasti Dip Blaze Green?
Simply peel it off. Start at an edge and pull slowly and steadily. If it's difficult, you can use a little mineral spirits or a specialized Plasti Dip remover to help loosen it.
Troubleshooting
Uneven finish or "fisheyes"
Ensure the surface is properly cleaned and free of contaminants. Check for adequate spray pressure and consistent distance from the surface. Stir or shake the can more frequently.
Coating is sticky or doesn't dry properly
Apply in thinner coats and allow sufficient drying time between applications. Avoid applying in excessively humid or cold conditions.
Peeling is difficult or leaves residue
Ensure enough coats were applied (minimum 4-5 for easier removal). If residue remains, it can often be rolled off with a finger or dissolved with a small amount of mineral spirits or Goo Gone, then cleaned thoroughly.
Color is not vibrant enough
Apply the recommended base coat of regular Plasti Dip White before applying the Blaze color. Ensure sufficient coats of the Blaze color have been applied.
Pros and Cons
Pros
- Easy to apply and remove for temporary customization.
- Provides a protective, flexible rubber layer.
- Unique fluorescent green color stands out.
- Can be applied to a wide variety of materials.
Cons
- Requires a base coat of regular Plasti Dip for best color results.
- Durability may be less than permanent paint finishes.
- Can be challenging to achieve a perfectly smooth finish without practice.
- May require multiple coats for full coverage and opacity.
Setup, Compatibility & Care Instructions
Setup:
- Ensure the surface is clean, dry, and free of grease, oil, and debris.
- Mask off any areas you do not wish to coat.
- For optimal color vibrancy, apply 2-3 coats of regular Plasti Dip in White as a base first.
- Shake the can vigorously for at least one minute before and occasionally during use.
Application:
- Hold the can 6-10 inches away from the surface.
- Apply in thin, even coats, using a steady back-and-forth motion.
- Allow 10-30 minutes of drying time between coats (depending on temperature and humidity).
- Apply 4-6 total coats for best results, especially for Blaze colors.
Compatibility:
Plasti Dip adheres well to most surfaces including metal, plastic, wood, concrete, glass, and more. It is not recommended for use on surfaces that reach extremely high temperatures or are constantly exposed to gasoline.
Care:
Clean coated surfaces gently with mild soap and water. Avoid abrasive cleaners or tools that could damage the rubberized coating. To remove, simply peel it off.