No More Nails Grab Adhesive - UniBond - White
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later or explore other options below.
Product Information
Full details
This guide is for DIY enthusiasts and homeowners needing a reliable, heavy-duty adhesive for indoor and outdoor projects. The UniBond No More Nails Waterproof Grab Adhesive offers a strong, flexible, and water-resistant bond, eliminating the need for nails or screws. Its primary caveat is that it requires sufficient surface preparation and curing time for optimal performance.
All features
| Colour | White |
|---|---|
| Model Part Number | 3031746 |
| Brand | Unibond |
Extended Product Information
FAQs
Is this adhesive suitable for outdoor use?
Yes, UniBond No More Nails Waterproof is weather-resistant and ideal for various outdoor DIY projects.
Can I use this in a wet bathroom environment?
Absolutely. Its water-resistant properties make it perfect for bonding bathroom fixtures and fittings where moisture is present.
How long does it take to fully cure?
Full strength is typically achieved within 24 to 48 hours, but this can vary depending on temperature, humidity, and the amount of adhesive used.
Can I paint over the adhesive once it's cured?
Generally, most paints can be applied over the cured adhesive. However, it's advisable to test compatibility on a small, inconspicuous area first.
What materials can it bond?
It bonds a wide range of materials including brick, metal, ceramic, wood, plaster, concrete, and many plastics. It's not suitable for polystyrene or silicone.
How do I clean up uncured adhesive?
Wipe away any excess uncured adhesive immediately with a damp cloth. Once cured, it will need to be removed mechanically.
Does it need special tools for application?
It is typically applied from a cartridge using a standard sealant gun. Ensure the nozzle is cut to the desired bead size.
Troubleshooting
Adhesive not sticking well
Ensure surfaces are thoroughly cleaned, dried, and free from dust or grease. Check if materials are compatible and if surfaces were lightly abraded if non-porous.
Item is slipping after application
The instant grab may not be sufficient for very heavy items without temporary support. Use tape, props, or a temporary fixing method until the adhesive has fully cured (24-48 hours).
Difficulty extruding adhesive
Ensure the nozzle is properly cut and the cartridge is at room temperature. If using a cartridge gun, ensure it's properly loaded and functioning.
Adhesive remains tacky after 48 hours
This can occur in very high humidity or low temperatures. Ensure the product is within its recommended application temperature range and allow more time for curing. Ensure good ventilation.
Pros and Cons
Pros
- Excellent water resistance for damp environments.
- Strong instant grab reduces installation time.
- Flexible bond tolerates movement and vibrations.
- Solvent-free formulation is safer to use.
- Versatile for bonding a wide range of materials.
- Eliminates the need for drilling and mechanical fasteners.
Cons
- Requires proper surface preparation for best adhesion.
- Curing time is necessary for full strength, especially in humid conditions.
- May not be suitable for extremely heavy or load-bearing structural applications without additional support.
- Cleanup of excess adhesive needs to be done before it cures.
- Application temperature range might be limited.
Setup, Compatibility & Care
Setup:
- Ensure surfaces are clean, dry, and free from dust, grease, and loose material.
- For non-porous surfaces, lightly abrade to improve adhesion.
- Apply adhesive in a zig-zag pattern to one surface.
- Press the items firmly into place. For heavier items, an initial temporary support might be needed until the adhesive cures.
- Allow adequate curing time; full strength is typically reached after 24-48 hours, depending on temperature and humidity.
Compatibility:
This adhesive is suitable for a wide range of materials including wood, metal, ceramic, brick, concrete, plaster, and many plastics. It is not recommended for use on polystyrene, polypropylene, or PTFE. Always test on an inconspicuous area first if unsure.
Care:
Store in a cool, dry place, away from direct sunlight and frost. Keep the cap tightly closed when not in use. Clean up any excess uncured adhesive immediately with a damp cloth. Cured adhesive can be removed mechanically.