Evo-Stik TX528 Thixotropic Contact Adhesive - 1 Litre - Brown
Not Available
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later or explore other options below.
Product Information
Full details
This guide is for anyone using Evo-Stik TX528 Thixotropic Contact Adhesive for bonding various materials. The adhesive provides a high-strength, non-drip bond, perfect for overhead applications. A key consideration is the appropriate surface preparation to achieve optimal results. This guide will cover everything you need to know, from features and applications to troubleshooting common issues.
All features
| Colour | Brown |
|---|---|
| Model Part Number | 30603375 |
| Brand | Evo-Stik |
Extended Product Information
FAQs
What materials can I bond with Evo-Stik TX528?
It is suitable for bonding decorative plastic sheets, rigid plastics (PVC, ABS), wood, metal, wood composite boards, cane fibre boards, and acoustic tiles.
How should I prepare the surfaces before applying the adhesive?
Surfaces should be clean, dry, and free from dust, grease, and loose particles. Lightly roughen non-porous surfaces for better adhesion.
How much area does a 1-litre tin cover?
Approximately 4-6 m² per litre per coat, depending on the surface.
How long should I wait for the adhesive to dry before joining the surfaces?
Allow the adhesive to become touch dry, typically 10-20 minutes, depending on environmental conditions.
What should I do if the adhesive gets on my skin?
Avoid prolonged contact. Wash the affected area immediately with soap and water.
How should I store Evo-Stik TX528?
Store in a cool, dry place, away from extreme temperatures and direct sunlight.
Can I use this adhesive outdoors?
While the product is temperature-resistant, it's best to check for specific outdoor applications and ensure the materials are suitable for the environment.
What is the shelf life of the adhesive?
Check the product packaging for the specific shelf life. Always use the product within its expiration date.
Troubleshooting
Bonding failure or weak bond
Ensure surfaces were properly prepared (clean, dry, and roughened if necessary). Make sure enough adhesive was applied and that the surfaces were allowed to dry to a touch-dry state before joining. Apply sufficient pressure when joining the surfaces.
Adhesive is stringing or dripping
This is unlikely due to the thixotropic nature of the adhesive. Check for application errors or use a thicker application if necessary. Ensure the product is within its expiration date and has been stored correctly.
Adhesive takes too long to dry
Ensure the application environment is within the recommended temperature and humidity range. If the room is too cold or humid, drying times may increase.
Strong odor during application
Ensure the application area is well-ventilated. Although the product has low odor, ventilation will help minimize any residual smell.
Pros and Cons
Pros
- Non-drip formula prevents mess and waste, especially in overhead applications.
- Provides a strong and permanent bond.
- Suitable for a wide range of materials, increasing its utility.
- The thixotropic nature allows for some repositioning during application.
- Low odor makes it more pleasant to work with than some other adhesives.
- Good temperature resistance ensures the bond's longevity.
Cons
- Requires careful surface preparation for optimal adhesion.
- Coverage is dependent on the surface, which may require multiple coats on porous surfaces.
- Bonding requires applying adhesive to both surfaces.
- May not be suitable for all types of plastics; always check compatibility.
- Working time is limited before the bond sets.
Setup, Compatibility & Care
- Surface Preparation: Ensure surfaces are clean, dry, and free from dust, grease, and loose particles. Lightly roughen non-porous surfaces for better adhesion.
- Application: Apply a thin, even coat of adhesive to both surfaces to be bonded. Allow the adhesive to become touch dry (usually 10-20 minutes). Place the surfaces together, and apply firm, even pressure for a few seconds.
- Compatibility: Compatible with wood, metal, wood composite boards, decorative plastic sheets, PVC, ABS, cane fibre boards and acoustic tiles. Always test on a small, inconspicuous area first, especially with unfamiliar materials.
- Coverage: Approximately 4-6 m² per litre per coat, depending on the surface. Apply one coat on each surface to be bonded.
- Care: Store in a cool, dry place. Avoid extreme temperatures. Clean up excess adhesive immediately with a suitable solvent (e.g., acetone or a solvent recommended by the manufacturer) while it is still wet.