Gunson Dent Puller Kit - 77175
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later or explore other options below.
Product Information
Full details
This Gunson Dent Puller Kit (77175) is designed for DIY enthusiasts and auto repair professionals looking to remove or significantly reduce small dents and dings from vehicle bodywork without professional respraying. Its key benefit is offering a cost-effective, paintless repair solution. A potential caveat is that it's best suited for smaller imperfections and may not handle deep creases or large impact damage.
All features
| Model Part Number | 77175 |
|---|---|
| Brand | GUNSON |
Extended Product Information
FAQs
What size dents can this kit handle?
The kit is most effective on small to medium-sized dents and dings, typically those that haven't creased the metal sharply or are on relatively flat surfaces.
Does this kit damage the paint?
When used correctly, this paintless dent removal kit is designed not to damage the original paintwork. However, improper technique or excessive force could potentially cause issues.
How many times can I use the glue sticks?
The number of uses depends on the size of the dents and how much glue is applied per pull. The kit includes two sticks, and spares are available.
Can I use this kit on plastic bumpers?
This kit is primarily designed for metal body panels. Its effectiveness on plastic bumpers may vary and is not guaranteed.
What is the purpose of the pencil punch?
The paintless dent removal pencil punch is used for fine adjustments. It can help to gently tap down any high spots that may remain after pulling the dent, or to carefully work the edges of a repair.
Is the glue safe for car paint?
The special PDR glue used is formulated to be strong enough to pull metal but designed to release cleanly without damaging automotive paint when used with the release agent.
What is the power requirement for the glue gun?
The glue gun is 240V mains powered and comes with a standard BS (UK) plug.
Troubleshooting
Glue not dispensing from the gun
Ensure the glue gun has reached its full operating temperature. Check that the glue stick is properly loaded and hasn't run out. Verify the power connection.
Pulling tab not adhering to the panel
Clean the panel surface thoroughly to remove dirt or grease. Ensure the glue is applied hot and directly onto the center of the dent. Press the tab firmly for a few seconds.
Dent is not lifting sufficiently
Apply more hot glue and allow it to cool slightly longer before pulling. Try using a different sized pulling tab if available. Consider a second pull from a slightly different angle or with more gradual force. This kit is best for smaller dents.
Difficulty removing the pulling tab
Apply the release agent generously around the base of the tab where it meets the glue. Allow it to penetrate for a minute before gently twisting or prying the tab off. Avoid excessive force that could damage the paint.
Glue residue left on the paintwork
Use the glue scraper gently once the glue has cooled. For stubborn residue, the release agent can help soften it. Clean the area with a mild car wash soap and water.
Pros and Cons
Pros
- Cost-effective alternative to professional bodywork for small dents.
- Paintless repair preserves original vehicle finish.
- All-in-one kit provides necessary tools to start repairs.
- Suitable for use by both DIYers and experienced technicians.
- Compact and easy to store.
Cons
- Effectiveness may be limited on larger or sharper dents.
- Requires practice to achieve optimal results.
- Glue removal can sometimes be challenging if not done correctly.
- 40W glue gun might take time to reach optimal temperature.
- Primarily suited for relatively flat body panels.
Setup, Compatibility & Care
Setup:
- Insert a glue stick into the 40W glue gun.
- Plug the glue gun into a 240V mains socket (UK plug).
- Allow the glue gun to heat up for approximately 5-10 minutes until the glue flows smoothly.
- Ensure the dented area on the vehicle is clean and dry.
Compatibility:
- This kit is designed for use on vehicle bodywork with intact paint.
- It is most effective on metal panels.
- The 240V mains powered glue gun requires a standard UK electrical outlet.
Care:
- After use, allow the glue gun to cool completely before cleaning.
- Wipe the glue gun with a dry or slightly damp cloth. Avoid submerging it in water.
- Clean the pulling tabs and bridge with a damp cloth. Ensure all glue residue is removed.
- Store all components in a dry place, preferably in the original packaging or a dedicated tool case.
- Periodically check the glue gun's power cord for any damage.