Tetrion Powerfil 2K 2 Part Body Filler - Lightweight - White - 600g
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later or explore other options below.
Product Information
Full details
The Tetrion Powerfil 2K 2 Part Body Filler is designed for DIY enthusiasts and professionals tackling a variety of repair jobs on metal, wood, stone, and most plastics. Its key benefit is a super smooth, tough, and sandable finish that sets rapidly, allowing for quick project completion. A primary consideration is the precise mixing ratio required for optimal performance, as incorrect proportions can affect setting times and durability.
All features
| Model Part Number | TETTPW600 |
|---|---|
| Brand | Tetrion |
Extended Product Information
FAQs
What is the correct mixing ratio for Tetrion Powerfil?
The recommended ratio is 1 part hardener to 50 parts filler. A visual guide is a pea-sized amount of hardener to a golfball-sized amount of filler.
How long does it take for the filler to set and become sandable?
At an ambient temperature of 18°C (65°F), the filler will start to set after 5 minutes and will be fully cured and sandable after approximately 20 minutes.
Can I use Tetrion Powerfil on painted surfaces?
Yes, provided the painted surface is sound and properly prepared (clean, dry, and free from grease). It can be painted over once cured.
What is the shelf life of Tetrion Powerfil?
Unopened, the filler and hardener should be stored in a cool, dry place. Refer to the product packaging for specific expiry dates, but typically they have a good shelf life if stored correctly.
Can I use this filler outdoors?
Yes, it is suitable for outdoor use on appropriate materials. However, avoid applying it in extreme temperatures or wet conditions. Ensure adequate ventilation during application and curing.
What happens if I use too much hardener?
Using too much hardener will cause the filler to set much faster, potentially making it difficult to apply and shape. It can also lead to a harder, more brittle finish that may be prone to cracking.
How should I store leftover filler and hardener?
Never return unused mixed paste to the original tin. Unmixed filler and hardener should be stored in their original, tightly sealed containers in a cool, dry environment.
Troubleshooting
Filler not hardening or setting too slowly
Ensure the correct mixing ratio (1 part hardener to 50 parts filler) is used. Check the ambient temperature; cooler conditions will slow the cure time. Make sure the hardener is not expired.
Filler hardening too quickly
This usually occurs in warmer temperatures. Mix smaller batches of filler at a time to allow for sufficient working time. Ensure the filler and hardener are not stored in direct sunlight or heat.
Poor adhesion to the surface
The surface may not have been prepared correctly. Ensure it is free from dirt, grease, moisture, and loose material. Sanding the surface lightly before application can also improve adhesion.
Filler is difficult to sand
Wait until the filler is fully cured before sanding. If it's still difficult, you may have used too much hardener, or the ambient temperature was very low during curing, requiring more time. Ensure you are using appropriate sandpaper grit.
Pros and Cons
Pros
- Sets quickly, allowing for rapid completion of repairs.
- Highly versatile, suitable for a wide range of materials.
- Achieves a smooth, sandable surface for excellent finishing.
- Can be drilled and screwed into after curing for added functionality.
- Includes essential application tools in the kit.
Cons
- Requires precise mixing ratio; incorrect ratios can impact performance.
- Setting time is temperature-dependent, requiring adjustments in different conditions.
- Not suitable for use in excessively hot or cold conditions without adaptation.
- Unused paste cannot be returned to the tin, leading to potential waste if mixed in excess.
- Requires proper surface preparation for optimal adhesion.
Setup, Compatibility & Care
Setup:
- Ensure the surface to be treated is clean, dry, and free from grease, dirt, and loose material.
- Gather clean mixing equipment.
- Mix 1 part hardener with 50 parts filler (approximately a pea-sized amount of hardener to a golfball-sized amount of filler). Mix thoroughly until no streaks are visible and the hardener is fully dispersed.
- Apply the mixed filler immediately using the provided spreader.
Compatibility:
This filler is suitable for use on metal, wood, stone, and most common plastics. Always test on an inconspicuous area if unsure about plastic compatibility.
Care:
- Store the filler and hardener in a cool, dry place.
- Keep paste cool in summer and warm in winter to maintain optimal consistency.
- Clean all tools and equipment immediately after use with water.
- Never return unused mixed paste to the original containers.