JB Weld Plasticweld Epoxy Repair Putty - White
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later or explore other options below.
Product Information
Full details
J-B Weld PlasticWeld Epoxy Repair Putty is designed for DIYers and professionals needing to repair and rebuild plastic components. Its key benefit is a strong, durable bond that can be easily shaped and finished after curing. A potential caveat is the relatively short 25-minute working time, which requires prompt application once mixed.
All features
| Colour | White |
|---|---|
| Brand | JB Weld |
Extended Product Information
FAQs
How long does J-B Weld PlasticWeld Epoxy Repair Putty last once mixed?
Once mixed, you have approximately 25 minutes of working time before the putty begins to set. It will be hard enough to handle in about an hour and fully cured in 24 hours.
Can I use this on painted plastic?
Yes, it can be used on painted plastic, provided the paint is well-adhered to the surface. For best results, lightly sand the painted surface to provide a better key for the epoxy.
What is the temperature range for using this putty?
The putty should be applied and cured in temperatures between 50°F (10°C) and 70°F (21°C) for optimal results. Curing may be slower at lower temperatures.
Can this putty be used for underwater repairs?
Once fully cured, the J-B Weld PlasticWeld Epoxy Repair Putty can withstand immersion in water. However, it is best applied and allowed to cure above water.
How much material is in each stick?
Each stick contains 57g (2oz) of epoxy putty. The 2-pack provides a total of 114g (4oz).
Can I drill and tap threads into the cured putty?
Yes, once fully cured, the putty can be drilled, tapped, sanded, and painted, allowing for extensive post-repair modification.
Will this putty bond to metal?
While primarily formulated for plastics, J-B Weld PlasticWeld may adhere to some metals. However, for metal-to-metal or metal-to-plastic applications, a dedicated J-B Weld product for those materials might offer superior performance.
Troubleshooting
Putty does not harden
Ensure the putty was kneaded thoroughly until a uniform color was achieved. In cold temperatures, warmth may be needed to initiate curing. Check expiration date if applicable.
Putty cures too quickly
Work in smaller batches if a larger repair is needed. Ensure the working environment is not excessively warm.
Poor adhesion to plastic
The surface may not have been properly cleaned and prepared. Remove the putty, clean the surface thoroughly, and lightly abrade it before reapplication.
Putty is sticky after curing
This can indicate incomplete mixing or curing. Allow additional time for full cure, or ensure proper mixing ratios were achieved by kneading thoroughly.
Pros and Cons
Pros
- Easy to use with no measuring required.
- Fast setting time allows for quick repairs.
- Cured material is fully machinable for finishing.
- Strong bond strength suitable for many plastic applications.
- Works on a variety of common plastic types.
- Comes in a convenient 2-pack.
Cons
- Limited working time requires quick application.
- The off-white color may not match all plastics without painting.
- May not be suitable for extremely high-heat or high-flex applications.
- Requires manual mixing, which can be messy if not handled carefully.
- Bond strength is rated for plastic-to-plastic adhesion; compatibility with other materials may vary.
Setup, Compatibility & Care
Setup:
- Preparation: Ensure the plastic surface is clean, dry, and free of grease, oil, or contaminants. Lightly abrading the surface with sandpaper can improve adhesion.
- Mixing: Cut off the required amount of putty. Knead the putty with gloved fingers until it achieves a uniform color (typically gray or off-white), indicating the resin and hardener are fully blended. This process usually takes 1-2 minutes.
- Application: Apply the mixed putty immediately to the prepared surface. Press firmly into the damaged area and mold it to the desired shape.
Compatibility:
This putty is specially formulated for bonding to most rigid and semi-rigid plastics, including:
- PVC
- ABS
- Fiberglass
- Some Polyethylene (PE) and Polypropylene (PP) plastics (test adhesion first)
- Other rigid plastics
It is not recommended for use on flexible plastics or materials that undergo significant expansion and contraction.
Care:
- Store unused putty in its original packaging in a cool, dry place away from direct sunlight.
- Keep the packaging sealed to prevent premature curing.
- Once cured, the repaired area can be cleaned with standard household cleaners. Avoid harsh solvents that could degrade the plastic or the epoxy.