Tetrosyl Brushable Seam Sealer - TETBSS001PK4
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later or explore other options below.
Product Information
Full details
The Tetrosyl Brushable Seam Sealer is designed for automotive professionals and DIY enthusiasts seeking robust protection for overlap seams against dust and water ingress. Its key benefit is providing a permanently flexible, non-slumping seal suitable for various joint types. A potential caveat is the required preparation time and curing before overcoating.
All features
| Model Part Number | TETBSS001PK4 |
|---|---|
| Brand | Tetrosyl |
Extended Product Information
FAQs
How long does it take to dry?
The Tetrosyl Brushable Seam Sealer dries to the touch in approximately 2 hours at 20°C. Full curing time will be longer and depends on temperature and humidity.
Can I use this on exterior trim?
This product is specifically designed for sealing overlap seams on car bodies to protect against dust and water penetration. Its suitability for exterior trim would depend on the specific application and material, but it's primarily intended for seams.
What surfaces can I apply this to?
It can be applied to properly prepared and degreased metal surfaces, common in automotive overlap seams.
How many coats should I apply?
A maximum of two coats is recommended for optimal performance and coverage.
Can I use any type of paint over this sealer?
Once fully cured, it can be overcoated with nitro-cellulose, acrylic, or synthetic refinishing paint systems.
What is the best way to apply it?
Apply a smooth, even coat with a nylon bristle brush, always brushing in the same direction.
How should I store the product?
Store the container in a cool, dry place away from direct sunlight and extreme temperatures.
Troubleshooting
Sealer not adhering to the surface
Ensure the surface was thoroughly cleaned and degreased with Tetrosyl Compliant Panel Wipe before application. Any residue or contamination will affect adhesion.
Sealer sagging or running on vertical surfaces
This indicates over-application or that the product has not yet developed its non-slumping characteristics. Apply thinner coats and ensure the initial coat has started to set before applying a second if necessary.
Peeling or cracking after painting
The seam sealer may not have been fully cured before being painted over. Allow adequate drying and curing time according to the environmental conditions.
Difficult to brush evenly
Ensure the product is at an appropriate temperature. If too cold, it may be stiff. If too warm, it may be too thin and run. Use a suitable nylon bristle brush.
Pros and Cons
Pros
- Provides excellent protection against water and dust ingress.
- Remains flexible, adapting to joint movement.
- Suitable for use on both horizontal and vertical surfaces.
- Can be painted over, integrating with existing finishes.
- Relatively fast drying time.
Cons
- Requires a properly prepared and degreased surface for optimal adhesion.
- Needs sufficient curing time before being painted over.
- Application is best done with a specific type of brush (nylon bristle).
- Only one product is recommended for surface preparation (Tetrosyl Compliant Panel Wipe).
Setup, Compatibility & Care
Preparation:
Ensure the surface is clean, dry, and free from contaminants. Degrease the area thoroughly using Tetrosyl Compliant Panel Wipe. Proper surface preparation is crucial for adhesion and long-term performance.
Application:
- Stir the product if necessary.
- Apply a smooth, even coat using a clean nylon bristle brush.
- Always brush in the same direction to ensure a consistent finish.
- A maximum of two coats is recommended.
Drying & Curing:
The product dries to the touch in approximately 2 hours at 20°C. Allow sufficient time for full curing before overcoating or exposing to the elements.
Overcoating:
Once fully cured, the seam sealer can be overcoated with nitro-cellulose, acrylic, or synthetic refinishing paint systems.
Storage:
Store the container in a cool, dry place away from direct sunlight and extreme temperatures.