AB Tools Unifine Air Under Seal Under Coating Under Body Spray Gun Schutz Schultz - TE339
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later or explore other options below.
Product Information
Full details
This air-powered undersealing gun is designed for automotive professionals and DIY enthusiasts applying underbody coatings. Its key benefit is efficient and consistent application of schutz-type products, ensuring thorough coverage with trigger-controlled precision. A minor consideration is its average air consumption of 11 CFM, requiring an adequate air supply. It features trigger operation, a 1/4" BSP male air inlet, and is suitable for use with standard 1L schutz cans, offering a spray distance of 12-18 inches. The gun is lightweight, easy to clean, and designed for low maintenance.
All features
| Model Part Number | TE339 |
|---|---|
| Brand | AB Tools |
Extended Product Information
FAQs
What type of coatings can I use with this gun?
This gun is designed for use with schutz-type underbody coatings that come in standard 1-litre cans. Always refer to the coating manufacturer's recommendations for suitability with spray application equipment.
What air pressure should I use?
The gun is suitable for use up to 80 psi. It is recommended to start with a lower pressure and adjust as needed, ensuring consistent air flow.
How do I connect it to my air compressor?
The gun features a 1/4" BSP male air inlet. You will need a compatible air hose and fitting for your compressor.
How far away should I hold the gun from the surface?
The optimal spray distance for this gun is between 12 and 18 inches from the surface you are coating.
Does this gun come with any hoses or cans?
This product is the spray gun only. Air hoses and undercoating cans are sold separately.
What is the average air consumption?
The average air consumption is 11 CFM. Ensure your air compressor can supply this volume of air to operate the gun effectively.
How do I clean the gun after use?
Immediately after use, disconnect from air and remove the can. Flush the gun with the recommended cleaning solvent for the undercoating product you used until clear. Refer to the care instructions for detailed steps.
Troubleshooting
No material is spraying
Check air supply is connected and pressurized. Ensure the schutz can is properly seated and not empty. Verify the trigger is being depressed fully. Clean any blockages in the nozzle or internal passages.
Uneven spray pattern
Adjust the spray distance (12-18 inches). Ensure the can is not empty and has sufficient material. Check for consistent air pressure. Clean the nozzle for obstructions.
Air leaks from the connection
Ensure the air hose is securely connected to the 1/4" BSP inlet. Check the integrity of the air hose O-ring or fitting. Tighten any loose connections.
Material sputtering
The can may be low on product or not properly sealed. Ensure the can is securely attached. Check for air bubbles in the fluid path. Clean the nozzle and internal passages.
Gun is difficult to clean
Clean the gun immediately after use before the undercoating material dries. Use the recommended cleaning solvent for the specific undercoating product you are using. Flush thoroughly.
Pros and Cons
Pros
- Efficient and consistent application of undercoating.
- Precise trigger control for varied coverage.
- Lightweight and easy to handle.
- Designed for low maintenance and ease of cleaning.
- Compatible with standard 1L schutz cans.
Cons
- Requires an air compressor with adequate air supply (11 CFM average consumption).
- Maximum operating pressure of 80 psi may limit some heavy-duty applications.
- Spray distance may require practice for perfect results.
- Primarily designed for underbody coatings, not general spraying.
Setup, Compatibility & Care
Setup:
- Ensure your air compressor is turned off and depressurized.
- Connect the air hose to the 1/4" BSP male air inlet on the gun. Ensure a secure connection.
- Screw a compatible 1L schutz can firmly into the gun's receptacle. Check for a snug fit to prevent leaks.
- Set your air compressor to the desired pressure, not exceeding 80 psi.
Compatibility:
- Air Inlet: 1/4" BSP Male.
- Air Pressure: Up to 80 psi.
- Coating Cans: Standard 1-litre schutz cans. Fits most standard 1 litre containers.
- Air Consumption: Average 11 CFM.
Care:
- After Use: After each use, thoroughly clean the gun to prevent material from drying and clogging the internal parts.
- Cleaning Procedure: Disconnect from air and remove the can. Refer to the undercoating product's instructions for recommended cleaning solvents. Typically, flush the gun with the appropriate solvent by running it through the system or by spraying solvent into a waste container until clear.
- Storage: Store in a clean, dry place. Ensure no residual material remains in the nozzle or internal passages.