Araldite Rapid Epoxy Adhesive - 2 X 15Ml Tubes
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later or explore other options below.
Product Information
Full details
The Araldite Rapid Epoxy Adhesive is for DIY enthusiasts and homeowners needing quick, strong repairs. Its key benefit is a fast-setting, durable two-part epoxy bond suitable for multiple materials. A caveat is the smaller working time compared to slower-setting epoxies, requiring prompt application. This product features a fast-setting formula, a strong two-part epoxy bond, versatility across various materials, and easy twin-tube mixing for precise application.
All features
| Brand | Araldite |
|---|
Extended Product Information
FAQs
What is the working time of Araldite Rapid Epoxy?
The working time is relatively short due to its fast-setting nature, typically allowing for accurate application within a few minutes after mixing. Exact times can vary with temperature.
Can this adhesive be used on porous materials like wood?
Yes, Araldite Rapid Epoxy Adhesive is suitable for bonding wood, providing a strong and durable joint.
How long does it take to fully cure?
While it sets quickly for handling, full cure and maximum strength are typically achieved after several hours, though this can vary based on conditions.
What is the shelf life of Araldite Rapid Epoxy?
Unopened tubes, stored correctly in a cool, dry place, generally have a good shelf life. Refer to the packaging for specific expiry dates.
Can I use this to bond plastics?
Yes, it bonds many common plastics. However, it's recommended to test on a small, inconspicuous area first, as some plastics may not be compatible.
What is the color of the adhesive once cured?
The adhesive cures to an amber or translucent color.
How should I clean up uncured adhesive?
Wipe away any uncured excess adhesive with a damp cloth. For stubborn residue, consult the product's specific cleaning recommendations, as solvents may be required.
Troubleshooting
Adhesive not setting or setting very slowly
Ensure equal parts of resin and hardener were used and mixed thoroughly. Check that the ambient temperature is within the recommended range for curing. Old or improperly stored product may lose effectiveness.
Poor bond strength
Verify that the surfaces were clean, dry, and free from contaminants before application. Ensure adequate mixing of resin and hardener. Confirm that sufficient pressure was applied during the initial setting period.
Adhesive is too thick or difficult to mix
This can happen in cooler temperatures. Gently warm the tubes in warm water (do not overheat) before dispensing and mixing. Ensure both components are dispensed in equal quantities.
Difficulty in dispensing equal amounts
Carefully align the nozzles and dispense simultaneously. For very small amounts, consider dispensing onto a flat surface and then combining.
Pros and Cons
Pros
- Sets quickly for efficient repairs.
- Creates a strong and durable bond.
- Adheres to a wide variety of materials.
- Easy to mix and apply with precise control.
- Ideal for urgent fixes and DIY projects.
Cons
- Shorter working time requires fast application.
- May not be suitable for very large or complex repairs needing extended working time.
- The amber/translucent cured color may not match all materials.
- Requires careful measurement for optimal bond strength.
Setup, Compatibility & Care
Setup:
- Ensure both surfaces to be bonded are clean, dry, and free from dust or grease.
- Dispense equal amounts of resin and hardener onto a clean, disposable surface.
- Mix the two components thoroughly using the provided spatula or a clean tool until a uniform color is achieved.
- Apply the mixed adhesive to one or both surfaces, depending on the application.
- Press the parts together firmly and hold or clamp for the recommended setting time.
Compatibility:
This epoxy is compatible with metal, wood, ceramics, glass, rubber, and various plastics. Always test on an inconspicuous area of painted or plastic surfaces first to ensure compatibility.
Care:
Store unopened tubes in a cool, dry place away from direct sunlight. Once mixed, the adhesive has a limited pot life and should be used promptly. Clean up any uncured excess adhesive with a damp cloth or appropriate solvent (check product label for recommendations). Cured adhesive can be difficult to remove.