PowerTec Slide Hammer - 12 Glue Pads
Not Available
Not Available
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later or explore other options below.
Product Information
Full details
The PowerTec Slide Hammer with 12 Glue Pads is designed for vehicle owners and auto body professionals seeking an effective tool for paintless dent repair (PDR). It allows for the removal of minor to moderate dents and dings without compromising the vehicle's original paintwork, offering a key benefit of preserving finish integrity. A potential caveat is that optimal results often depend on the correct application of glue and appropriate slide hammer technique, which may require practice.
All features
| Model Part Number | 92376 |
|---|---|
| Brand | POWERTEC |
Extended Product Information
FAQs
What types of dents can this slide hammer repair?
This slide hammer is best suited for minor to moderate dents and dings on vehicle body panels, such as those caused by hail, door dings, or parking lot mishaps. It is most effective on relatively flat or gently curved surfaces where the metal is not severely creased or stretched.
Do I need a special glue gun?
Yes, you need a hot melt glue gun. Power-TEC recommends their Gluematic Glue Gun (Part No. 91237) and compatible glue sticks (Part No. 92342) for optimal performance with this slide hammer.
How many glue pads are included?
The PowerTec Slide Hammer kit comes complete with 12 assorted glue pads.
Are replacement glue pads available?
Yes, replacement glue pads are available separately under Part No. 92378.
Can I use this on plastic bumpers?
While primarily designed for metal vehicle bodywork, the slide hammer and glue pad system might be adaptable for minor repairs on some plastic bumpers, depending on the plastic type and the nature of the damage. Always test on an inconspicuous area first if attempting to use on plastic.
What is the length of the slide hammer?
The PowerTec Slide Hammer has a length of 460mm.
How do I clean the slide hammer and glue pads?
After use, carefully remove any residual glue from the connector tip and pads. A plastic scraper or isopropyl alcohol can help. Store them in a clean, dry environment to maintain their effectiveness.
Troubleshooting
Glue pad not adhering to the vehicle surface.
Ensure the surface is clean and free from dirt, grease, or wax. Make sure the hot melt glue is sufficiently hot and applied generously to the pad. Press the pad firmly onto the dent and allow adequate cooling time.
Slide hammer is not pulling the dent effectively.
Check if the glue pad is securely attached to the slide hammer. Ensure the glue has fully hardened before pulling. Try using a different size or shape of glue pad. Make sure you are using controlled, steady pulls.
Paint is lifting or cracking during the pulling process.
This may indicate the paint is already compromised or the pulling force is too aggressive. Use lighter, more frequent pulls. Ensure the dent is suitable for PDR. For severe damage or weak paint, consult a professional.
Difficulty removing the hardened glue.
Use a dedicated hot melt glue remover (e.g., Power-TEC Hot Melt Glue Remover, Part No. 92341) as recommended. Isopropyl alcohol can also help soften some glues. Gently scrape with a plastic tool if necessary, avoiding damage to the paint.
Pros and Cons
Pros
- Enables paintless dent repair, preserving original paintwork.
- Includes a comprehensive set of 12 assorted glue pads for versatility.
- User-friendly design suitable for both DIY enthusiasts and professionals.
- The 460mm length offers good leverage and reach.
- Designed for efficient and precise dent pulling.
Cons
- Requires a hot melt glue gun and specific glue sticks (sold separately).
- Effectiveness may vary depending on the size, depth, and location of the dent.
- A learning curve may exist for users new to paintless dent repair techniques.
- Replacement glue pads need to be purchased separately if worn out.
Setup, Compatibility & Care
Setup:
- Ensure you have a compatible hot melt glue gun (e.g., Power-TEC Gluematic Glue Gun, Part No. 91237) and appropriate glue sticks (e.g., Power-TEC glue sticks, Part No. 92342).
- Heat the glue gun and load a glue stick.
- Select an appropriate glue pad size and shape for the dent.
- Apply hot glue to the surface of the selected glue pad.
- Quickly and firmly press the glued pad onto the center of the dent, ensuring good adhesion.
- Allow the glue to cool and harden for 1-2 minutes.
- Attach the slide hammer's connector tip to the glue pad.
- Apply steady, controlled pulling force using the slide hammer to lift the dent.
- Remove the glue and pad after pulling (using Power-TEC Hot Melt Glue Remover, Part No. 92341, is recommended).
Compatibility:
- Primarily designed for use with hot melt glue guns and specific glue sticks (recommended: Power-TEC Part No. 91237 glue gun and Part No. 92342 glue sticks).
- Compatible with Power-TEC replacement glue pads (Part No. 92378).
- Suitable for use on most vehicle body panels where paintless dent repair is applicable.
Care:
- After each use, remove any residual glue from the slide hammer connector tip and glue pads.
- Store the slide hammer and glue pads in a clean, dry place, preferably in their original packaging or a protective case.
- Avoid exposing the glue pads to extreme heat or direct sunlight when not in use.
- Periodically inspect the glue pads for wear and tear; replace as needed.