Tikkurila Valtti Bio Terrace Oil - 1 Litre
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later or explore other options below.
Product Information
Full details
Tikkurila Valtti Bio Terrace Oil is designed for homeowners looking to protect and beautify their exterior wooden surfaces like terraces, furniture, and platforms. Its key benefit is providing maximum protection against moisture, dirt, and discoloration while preventing wood from cracking, thanks to its deep penetration. A minor caveat is that the product is pre-tinted brown, offering less flexibility in color choice for some users.
All features
| Model Part Number | Tikkurila Valtti Bio Terrace Oil |
|---|---|
| Brand | Tikkurila |
Extended Product Information
FAQs
What types of wood can I use Tikkurila Valtti Bio Terrace Oil on?
It is suitable for impregnated wood (pressure-treated wood), hardwood, heat-treated wood, and untreated wood. It can also be applied to previously oil-treated surfaces.
How long does it take for the oil to dry?
The surface typically becomes dry in approximately 3 hours, but this can vary depending on the porosity of the wood and environmental conditions.
Can I get this oil in colors other than brown?
No, Valtti Bio Terrace Oil is pre-tinted and available only in a classic brown shade to maximize protection.
What is the minimum volume in the can?
The minimum content is 900ml. Tikkurila cans are filled with 10% less volume than the unit measure to allow for the addition of colorants.
How should I apply the oil?
Apply evenly with a brush or sponge. It is recommended to apply thin coats and work the oil into the wood.
How often should I reapply the oil?
Reapplication frequency depends on the exposure and wear of the wooden surface, but typically it is recommended every few years to maintain optimal protection.
Is this product suitable for indoor use?
No, Tikkurila Valtti Bio Terrace Oil is specifically designed for exterior wooden surfaces.
Troubleshooting
Uneven color after application
Ensure the oil was stirred thoroughly before and during application. Apply thin, even coats, and avoid over-application in certain areas. Allow adequate drying time between coats.
Wood still appears to be absorbing water
The wood may require an additional coat. Ensure the surface was properly prepared and completely dry before the initial application. Check for any missed spots.
Surface remains sticky after drying
This can happen if too much oil was applied or if it was applied in very cold or humid conditions. Wipe off any excess oil with a clean cloth. In some cases, a light sanding might be necessary, followed by a very thin re-application if needed.
Product does not cover the stated area
Ensure the wood's porosity is considered. Highly absorbent woods will require more product. Apply in thin, even coats as recommended.
Pros and Cons
Pros
- Offers excellent protection against moisture and UV damage.
- Prevents wood from cracking, maintaining its structural integrity.
- Suitable for various wood types, including treated and untreated surfaces.
- Easy to apply by brush or sponge.
- Partly bio-based for a more sustainable option.
- Quick drying time minimizes project downtime.
Cons
- Available only in a pre-tinted brown color, limiting aesthetic options.
- The can may appear less than full due to volume reduction for tinting.
- Requires proper surface preparation for optimal results.
Setup, Compatibility & Care
Preparation: Ensure the wooden surface is clean, dry, and free from dirt, grease, and old coatings. For previously treated surfaces, remove any loose paint or varnish. Sanding may be required for a uniform finish, especially on bare wood.
Compatibility: This oil is suitable for a variety of wood types including impregnated wood (pressure-treated wood), hardwood, heat-treated wood, and untreated wood. It can be applied over previously oil-treated surfaces.
Application: Apply evenly with a brush or sponge. Work the oil into the wood surface. For best results, apply thin coats. Allow approximately 3 hours for the surface to dry before applying a second coat if needed, depending on wood porosity.
Care: Clean the treated surfaces periodically with water and a mild detergent. For more intensive cleaning, use a dedicated wood cleaner. Reapply the oil as needed, typically every few years, depending on exposure and wear, to maintain protection.