Liberon Superior Danish Oil - 2.5 Litre
Not Available
Not Available
Not Available
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later or explore other options below.
Product Information
Full details
This guide is for DIY enthusiasts and professionals seeking to enhance and protect both interior and exterior wooden surfaces. The key benefit is achieving a rich, natural satin-to-gloss finish while providing robust protection against daily wear and UV damage. A potential caveat is the need for proper surface preparation and application to achieve optimal results. Liberon Clear Superior Danish Oil 2.5L is a high-quality wood treatment that nourishes, protects, and beautifies wood using a blend of pure tung oil and natural oils, featuring UV filters for added defense against sun damage and a quick-drying formula.
All features
| Model Part Number | 039231 |
|---|---|
| Brand | Liberon |
Extended Product Information
FAQs
What is the coverage rate for Liberon Superior Danish Oil?
One litre of Liberon Superior Danish Oil covers approximately 10-12 square meters, depending on the absorbency of the wood.
How long does it take for the oil to dry completely?
The oil is fully dry in approximately 5 hours under normal conditions, allowing for recoating after this period.
Can this oil be used on previously varnished or painted wood?
No, the wood must be stripped back to bare wood for the oil to penetrate and protect effectively. It is not suitable for use over existing varnish or paint.
Is this oil suitable for kitchen worktops?
Yes, it is suitable for kitchen worktops and offers good resistance to water and heat. Ensure adequate coats are applied and allow for proper curing.
How should I clean up spills or tools after using this product?
Wipe up any spills immediately. Tools can be cleaned with white spirit before the oil dries.
Does the oil change the color of the wood significantly?
The oil enhances the natural color of the wood. It provides a rich, warm tone but does not typically add a strong tint. Always test on a small area first.
Can I apply this oil over a stain?
It is recommended to use this oil on bare wood. If applying over a stain, ensure the stain is fully dry and compatible, and test in an inconspicuous area first.
Troubleshooting
Uneven finish or blotchiness
Ensure excess oil was wiped off thoroughly after each application. Uneven absorption can occur on woods with varied densities; apply thinner coats and ensure consistent wiping.
Wood still looks dry after application
The wood may be very absorbent. Apply additional thin coats, allowing adequate penetration time and wiping off all excess.
Slow drying time
Drying times are dependent on temperature and humidity. Ensure application in a well-ventilated area with moderate conditions. Thick application can also slow drying.
White residue after drying
This can happen if excess oil was not removed properly. Buff the area with a fine steel wool (grade 0000) and a clean cloth.
Pros and Cons
Pros
- Nourishes and protects wood effectively.
- Enhances the natural beauty and grain of wood.
- Provides excellent UV protection against sun damage.
- Offers resistance to water and heat.
- Quick drying time speeds up projects.
- Safe for use on children's toys.
Cons
- Requires careful application for best results.
- Multiple coats may be needed for deep protection.
- Surface preparation is crucial for optimal adhesion and finish.
- May alter the wood's color slightly due to oil saturation.
Setup, Compatibility & Care
Preparation: Ensure the wood surface is clean, dry, and free from dust, grease, and old finishes. Lightly sand the surface if necessary, starting with a coarser grit and finishing with a finer grit, then remove all dust.
Application: Apply Liberon Clear Superior Danish Oil thinly and evenly with a brush, cloth, or by dipping. Allow the oil to penetrate the wood for 15-30 minutes. Wipe off any excess oil thoroughly with a clean, lint-free cloth. Apply a second coat after 5 hours if desired, repeating the process. For interior use, up to three coats may be applied.
Compatibility: Suitable for all interior and exterior hardwoods and softwoods. Always test on an inconspicuous area first.
Care: Clean surfaces with a damp cloth. For re-oiling, ensure the surface is clean and dry, then apply a maintenance coat as needed.