UniBond No More Nails Heavy-Duty Mounting Adhesive - White
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later or explore other options below.
Product Information
Full details
The UniBond No More Nails Heavy-Duty Mounting Adhesive in white is designed for DIY enthusiasts and professionals undertaking interior fixing tasks who need a strong, nail-free solution. Its key benefit is providing instant grab and heavy-duty bonding without the need for drilling, preserving surfaces. A minor caveat is that it is primarily for interior use and works best on rigid building materials.
All features
| Colour | White |
|---|---|
| Brand | UniBond |
Extended Product Information
FAQs
Can this adhesive be used outdoors?
No, UniBond No More Nails Heavy-Duty Mounting Adhesive is specifically designed for interior applications only.
How long does it take for the adhesive to cure completely?
Full cure typically takes 24-48 hours, depending on temperature, humidity, and the materials being bonded. The instant grab provides initial hold within seconds.
What surfaces is this adhesive NOT suitable for?
It is not recommended for polyethylene, polypropylene, PTFE, or porous surfaces like damp plaster or untreated concrete. Always test on a small, inconspicuous area first if unsure.
How much surface area does one tube cover?
Coverage varies based on bead size and application. As a general guide, a 234g tube can provide approximately 10-15 metres of a 6mm zig-zag bead.
Can I use this adhesive for wallpapered surfaces?
It is suitable for application on some wallpapered surfaces, provided the wallpaper is well-adhered and the surface is rigid. However, testing on an inconspicuous area first is recommended to avoid potential damage.
Is this adhesive paintable once cured?
Once fully cured, the adhesive itself does not need to be painted as it is off-white. However, it does not typically affect the paintability of the surrounding materials if applied neatly.
Troubleshooting
Adhesive not dispensing
Ensure the nozzle is cut and the cartridge is properly loaded into the applicator gun (if applicable). Check if the product has expired.
Poor adhesion or bond failure
Verify that surfaces were clean, dry, and free from dust or grease. Ensure sufficient adhesive was applied and items were held in place long enough for the initial grab.
Slow setting time
Curing time can be affected by temperature and humidity. Ensure the application area is within the recommended temperature range and allow adequate time for the adhesive to cure fully before applying stress.
Low odour is not as expected
While the formula is low odour, some scent is present. Ensure the area is well-ventilated during application and curing if sensitivity is an issue.
Pros and Cons
Pros
- Provides strong, instant grab for quick fixes.
- Avoids the need for drilling or mechanical fasteners.
- Solvent-free formula is low in odour.
- Suitable for a variety of common interior building materials.
- Comes in a convenient 3-tube pack for multiple projects.
Cons
- Primarily designed for interior applications only.
- May not be suitable for very flexible or porous surfaces.
- Requires adequate ventilation during application, despite being low odour.
- Drying time may vary depending on environmental conditions and material porosity.
- A curing period is needed for maximum bond strength.
Setup, Compatibility & Care
Setup:
- Ensure surfaces to be bonded are clean, dry, and free from dust, grease, and loose material.
- Cut the nozzle tip to the desired bead size.
- Apply adhesive in a zig-zag pattern or as a series of dots to one surface.
- Press the items firmly into place within 10-15 minutes of application.
- Hold in position for at least 60 seconds to allow the instant grab to take effect.
Compatibility:
Suitable for wood, plaster, brick, concrete, ceramics, metal, and most rigid building materials. Not recommended for polyethylene, polypropylene, PTFE, or porous surfaces like damp plaster or untreated concrete. Always test on an inconspicuous area first if unsure.
Care:
Store unused adhesive in its original packaging in a cool, dry place, away from direct sunlight and frost. Ensure the nozzle is sealed after use. Clean up any excess uncured adhesive immediately with a damp cloth. Cured adhesive may be difficult to remove and may require mechanical means.