Metylan Woodchip Wallpaper Paste - MKR12 - 500g
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later or explore other options below.
Product Information
Full details
This guide is for DIY enthusiasts and professional decorators looking for a reliable adhesive for textured wallpapers. The Metylan Woodchip Wallpaper Paste MKR12 offers a powerful and secure bond for easy and dependable installation, ensuring a professional finish. A potential caveat is that it is specifically formulated for Raufaser and woodchip types, so suitability for other wallpaper materials should be confirmed.
All features
| Model Part Number | MKR12 |
|---|---|
| Brand | Metylan |
Extended Product Information
FAQs
Is Metylan MKR12 suitable for all types of wallpaper?
Metylan MKR12 is specifically formulated for Raufaser and woodchip wallpapers. It may not be suitable for vinyl, textile, or lightweight papers. Always check your wallpaper's specific adhesive requirements.
How much water should I use to mix the 500g pack?
The exact amount of water can vary slightly, but typically for a 500g pack, you would use approximately 4-5 liters of cold water. Always refer to the specific instructions on the packaging for the most accurate ratio.
What is the shelf life of the mixed paste?
Mixed paste should generally be used within a few hours (typically 24 hours maximum) and is best used fresh. Do not store mixed paste for extended periods, as its adhesive properties will degrade.
Can I use this paste on a newly plastered wall?
Yes, but ensure the new plaster is completely dry and has been properly sealed or primed to prevent the paste from being absorbed too quickly. Allow new plaster to cure fully as per the manufacturer's recommendations.
How do I clean up spills?
Any spills of the paste should be wiped up immediately with a damp cloth and clean water. Dried paste can be more difficult to remove.
Does this paste contain any harmful substances?
Metylan products are generally formulated with safety in mind for home use. Refer to the product packaging or Metylan's official website for detailed safety data sheets (SDS) if you have specific concerns.
Troubleshooting
Wallpaper is not sticking well or peeling at edges.
Ensure the correct mixing ratio was used and the paste was allowed to activate fully. Check that the wall surface was properly prepared and free of dust or grease. Reapply paste to the affected edges, ensuring even coverage.
Paste is too thick or too thin.
Adjust the water quantity slightly during mixing according to the product's instructions. For too thick, add a small amount of water; for too thin, ensure the correct powder-to-water ratio was initially followed. Mix thoroughly.
Lumps in the paste.
Stir the paste vigorously while adding the powder to the water. If lumps persist, try straining the paste through a sieve before application.
Wallpaper appears discolored after application.
Ensure the wall surface is clean and dry. Some older wall paints or stains can bleed through. Test on an inconspicuous area first if unsure. Ensure the paste was mixed with clean water.
Pros and Cons
Pros
- Provides a strong and durable bond for textured wallpapers.
- Simple to mix and apply, making the wallpapering process more manageable.
- Reliable performance ensures wallpaper stays in place without lifting.
- Suitable for Raufaser and woodchip wallpapers, offering specialized adhesion.
Cons
- Primarily designed for Raufaser and woodchip wallpapers; may not be optimal for other types.
- Requires proper mixing according to instructions for best results.
- Drying time may vary depending on environmental conditions.
Setup, Compatibility & Care
Setup:
- Preparation: Ensure the wall surface is clean, dry, and free from dust or old wallpaper residue. Prime if necessary, especially on porous surfaces.
- Mixing: Gradually add the Metylan MKR12 paste to the recommended amount of cold water while stirring continuously to achieve a lump-free, homogeneous consistency. Follow the mixing ratios specified on the packaging for optimal results.
- Activation: Allow the mixed paste to stand for the recommended resting time (usually indicated on the packaging) to fully activate.
Compatibility:
- This paste is specifically designed for Raufaser and woodchip wallpapers.
- It is generally suitable for use on most standard interior wall surfaces including plaster, drywall, and previously painted surfaces (ensure paint is stable).
- Always check the wallpaper manufacturer's instructions for specific adhesive recommendations.
Care:
- Store unused, sealed paste in a cool, dry place away from direct sunlight and frost.
- Clean any spills immediately with water.
- Dispose of empty packaging responsibly according to local regulations.