Power-TEC High Strength PDR Glue for Lateral Tension Pulls - 10 Piece Set - 92760
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later or explore other options below.
Product Information
Full details
This 10-piece set of Power-TEC High Strength PDR Glue sticks (92760) is designed for professional technicians performing Paintless Dent Repair (PDR), specifically for lateral tension pulling. Its primary benefit is a high-strength cure that sets in just 2 minutes, allowing for efficient dent repair. A key consideration is that it's optimized for use with the Power-TEC cordless glue gun (Part No. 92663) and requires a specific solvent spray (Part No. 92341) for removal.
All features
| Model Part Number | 92760 |
|---|---|
| Brand | POWERTEC |
Extended Product Information
FAQs
What is the primary use for these glue sticks?
These glue sticks are specifically designed for Paintless Dent Repair (PDR), particularly for techniques involving lateral tension pulling.
How long does it take for the glue to cure?
The glue has a fast cure time of approximately 2 minutes.
Do I need a special glue gun for these sticks?
Yes, they are optimized for the Power-TEC cordless glue gun (Part No. 92663) for best performance and reliable curing.
What is the best way to remove the glue residue?
It is recommended to use the Power-TEC solvent spray (Part No. 92341) for effective and residue-free removal.
What are the dimensions of each glue stick?
Each glue stick measures 300mm in length and 10mm in diameter.
How many glue sticks are included in this set?
This set includes 10 glue sticks.
Are these glue sticks suitable for general crafting purposes?
While they are hot melt glue sticks, their high-strength formulation is optimized for PDR. For general crafting, standard glue sticks might be more appropriate.
Troubleshooting
Glue not adhering properly
Ensure the surface is clean and free of grease or debris. Verify the glue gun is at the correct operating temperature and the glue stick is fully melted. Check compatibility with the glue gun.
Glue failing to cure within 2 minutes
Confirm ambient temperature is within optimal range for curing. Ensure a sufficient amount of glue was applied. Re-verify compatibility with the specified Power-TEC glue gun.
Difficulty removing the pull tab
Ensure you are using the recommended Power-TEC solvent spray (Part No. 92341). Apply the solvent generously around the edges of the tab and allow it to penetrate before attempting removal.
Glue gun is not dispensing glue
Check that the glue stick is properly loaded and pushed fully into the gun. Ensure the gun is adequately heated. Clean any potential clogs in the nozzle.
Pros and Cons
Pros
- Provides a strong bond essential for effective PDR.
- Fast cure time of 2 minutes maximizes workshop efficiency.
- Specifically formulated for lateral tension pulling techniques.
- Comes in a convenient 10-piece set for immediate use.
Cons
- Requires specific Power-TEC tools (glue gun and solvent spray) for optimal performance and removal.
- May not be suitable for all types of glue guns.
- Cure time might be too fast for inexperienced users needing more positioning time.
Setup, Compatibility & Care
Setup:
- Insert one 300mm glue stick into the Power-TEC cordless glue gun (Part No. 92663).
- Allow the glue gun to heat up to the optimal temperature as per the glue gun's manual.
- Apply the melted glue to the appropriate PDR pulling tab.
Compatibility:
- These glue sticks are specifically designed for use with the Power-TEC cordless glue gun (Part No. 92663).
- For residue-free removal, use Power-TEC solvent spray (Part No. 92341).
- While they are standard 10mm diameter, performance may vary with non-Power-TEC glue guns.
Care:
- Store glue sticks in a cool, dry place away from direct sunlight.
- Ensure the glue gun nozzle is clean after each use to prevent clogs.
- Keep the storage area clean and organized to avoid contamination.