Cellpack Wire Connector - 145624
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later or explore other options below.
Product Information
Full details
This guide is for telecommunication technicians and electricians working with solid and multi-wire telecom cables. The Cellpack 145624 Wire Connector provides a secure and corrosion-resistant connection for small-gauge wires, simplifying installation. A key caveat is its specific wire diameter and cross-section limitations, requiring careful selection. This connector features a grease filling for corrosion protection, a pull spring for secure connection, and a shock-resistant housing, enabling stripping, connection, and insulation in a single step.
All features
| Model Part Number | 145624 |
|---|---|
| Brand | CellPack |
Extended Product Information
FAQs
What type of wires is this connector designed for?
It is designed for solid and multi-wire telecom cables with a conductor cross-section between 0.4mm² and 0.9mm².
Does this connector require special tools?
Yes, a mechanical crimping plier is required for proper installation to ensure a secure connection.
How does the grease filling help?
The grease filling protects the internal electrical contact from moisture and air, preventing corrosion and ensuring a reliable connection over time.
Can this connector be used for power cables?
This connector is specifically designed for telecom applications and may not be rated for the current or voltage requirements of power cables. Always refer to the product specifications for intended use.
How many wires can be connected with one Cellpack 145624?
This is a single-conductor connector and supports a maximum of 2 cores, meaning it's ideal for joining two wires.
Is the connector reusable?
No, this type of connector is designed for single-use, permanent installation for optimal reliability.
What are the dimensions of the connector?
The connector is suitable for cables with a diameter of 1 - 2mm and a conductor cross section of 0.4 - 0.9mm².
Troubleshooting
Connection is loose or intermittent.
Ensure the correct wire gauge (0.4-0.9mm cross-section) is used. Verify that a mechanical crimping plier was used and applied sufficient, consistent pressure during installation.
Connector not making contact.
Check if the wire insulation was stripped correctly and to the appropriate length. Ensure the wires are fully inserted into the connector before crimping.
Corrosion observed on connection.
This is unlikely if installed correctly, as the grease filling is designed to prevent it. If corrosion is found, the connection may be compromised and should be replaced.
Difficulty inserting wires.
Ensure the wires are straight and not damaged. Check that the connector is oriented correctly and that no debris is obstructing the entry points.
Pros and Cons
Pros
- Corrosion-resistant due to grease filling.
- Streamlined installation process (strip, connect, insulate in one step).
- Compact and space-saving design.
- Durable, shock-resistant housing.
- Reliable electrical connection via U contact principle.
Cons
- Limited to specific wire diameters (0.4-0.9mm).
- Requires mechanical crimping pliers for proper installation.
- Not suitable for very large or very fine wires outside the specified range.
- Single conductor connector, may require multiple units for complex junctions.
- Transparent factory color may not be ideal for all aesthetic requirements.
Setup, Compatibility & Care Instructions
Setup:
- Ensure the wires to be connected are within the specified diameter range of 0.4mm to 0.9mm.
- Strip the insulation from the ends of the wires according to the connector's requirements (typically a small, precise strip length).
- Insert the stripped ends of the wires into the connector's designated slots.
- Use a mechanical crimping plier to apply pressure and create a secure connection. The U contact principle will engage, ensuring proper conductor contact.
Compatibility:
- Suitable for solid and multi-wire telecom cables.
- Compatible with conductor cross sections from 0.4mm² to 0.9mm².
- Supports a maximum of 2 cores per connector.
- Requires mechanical crimping pliers for installation.
Care:
- This connector is designed for single-use, permanent installation. No specific maintenance is typically required after proper installation.
- Store in a dry environment before use to prevent premature corrosion of internal components.
- Avoid exposing the connector to conditions outside its specified operating parameters.