GEN2 Wheel Bearing Hub Installer Remover Kit - Laser - 62mm-85mm
Not Available
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later or explore other options below.
Product Information
Full details
This guide is for anyone using the Laser GEN2 Wheel Bearing Hub Installer Remover Kit. It helps you efficiently remove and install wheel hubs and bearings on VAG models, saving time and effort. Note that while this kit is comprehensive, it's essential to ensure compatibility with your specific vehicle model before use.
All features
| Model Part Number | 5587 |
|---|---|
| Brand | Laser |
Extended Product Information
FAQs
What vehicles is this kit compatible with?
This kit is compatible with various Audi, Seat, Skoda, and Volkswagen models, including Audi A2, Seat Cordoba and Ibiza, Skoda Fabia and Roomster, and Volkswagen Fox, Lupo, Multivan, Polo, Touareg, and Transporter.
What wheel bearing diameters does the kit support?
The kit supports wheel bearings with diameters of 62mm, 66mm, 72mm, and 85mm.
Can I remove the bearing without removing the ABS sensor?
Yes, the kit includes an extraction adaptor specifically designed for removing bearings without needing to remove the ABS sensor.
Are spare parts available?
Yes, replacement spares such as the Force Nut (Part No. 0108), Force Screw (Part No. 0454), and Pin (Part No. 0622) are available.
How do I maintain the tools?
After each use, clean the tools and store them in a dry place. Regularly check the condition of the tools, especially the force nut, force screw, and pin, and replace them if necessary.
What should I do if the tool doesn't fit properly?
Double-check that you are using the correct adapter for your vehicle's wheel bearing diameter and model. Refer to the vehicle's service manual if necessary.
How do I deal with a difficult-to-remove bearing?
Ensure all components are aligned correctly. Apply penetrating oil to the bearing hub and allow it to sit for a while before attempting removal again. Use the force screw and nut properly.
Troubleshooting
The tool does not fit the hub correctly.
Double-check that you are using the correct adapter for your vehicle's wheel bearing diameter and model. Refer to the vehicle's service manual if necessary.
The bearing is difficult to remove.
Ensure all components are aligned correctly. Apply penetrating oil to the bearing hub and allow it to sit for a while before attempting removal again. Use the force screw and nut properly.
Damage to ABS sensor during removal.
If the ABS sensor gets damaged, ensure you are using the extraction adaptor and not applying excessive force. Consider replacing the sensor if it is damaged.
Pros and Cons
Pros
- Saves time by allowing for efficient removal and installation of wheel bearings.
- Preserves the ABS sensor during the removal process.
- Compatible with a wide range of VAG model vehicles.
- Includes all necessary components for the job.
- Spare parts are available for long-term use.
Cons
- Limited to VAG models (Audi, Seat, Skoda, Volkswagen).
- Requires some mechanical knowledge and experience.
- May require additional tools depending on the specific vehicle.
- Cannot be used on wheel bearings outside the specified diameter range.
Setup, Compatibility & Care
- Compatibility Check: Verify that the kit is compatible with your vehicle's make, model, and year. Specifically, confirm the wheel bearing diameter (62mm, 66mm, 72mm, or 85mm).
- Tool Preparation: Ensure all tools are clean and in good condition before use. Inspect the kit components for any signs of wear or damage.
- Vehicle Preparation: Safely raise and secure the vehicle. Remove the wheel and any components that obstruct access to the wheel bearing hub.
- Application: Use the correct adapter and tools from the kit to remove the old bearing and install the new one, following the manufacturer's instructions for your vehicle.
- Care: After each use, clean the tools and store them in a dry place. Regularly check the condition of the tools, especially the force nut, force screw, and pin, and replace them if necessary using the Laser spare parts.
Compatibility: This kit is designed for Audi A2, Seat Cordoba and Ibiza, Skoda Fabia and Roomster, and Volkswagen Fox, Lupo, Multivan, Polo, Touareg, and Transporter models. Always double-check your vehicle's specifications to ensure compatibility before use.