Loctite All Plastics Glue 2G + Activator Pen (3 Pack) - White
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later or explore other options below.
Product Information
Full details
The Loctite All Plastics Glue 2g + Activator Pen (3 Pack) is for users needing to bond difficult plastics that standard glues cannot handle. Its key benefit is a powerful dual-action system that reliably bonds even low-energy plastics like PE, PP, and PTFE. A potential caveat is that while it sets in seconds, full strength develops over time, requiring patience for heavy-duty applications.
All features
| Colour | White |
|---|---|
| Brand | Loctite |
Extended Product Information
FAQs
Can this glue be used on clear plastics without leaving a white residue?
Yes, the Loctite All Plastics Glue dries clear, making it ideal for neat, invisible repairs on clear plastic items.
How long does it take for the glue to reach full strength?
While the glue sets in seconds, full bond strength develops over a period of up to 24 hours. Avoid stressing the bond during this time.
Is the activator pen necessary for all plastics?
The activator is crucial for bonding low-energy plastics like PE, PP, and PTFE. For denser plastics or materials like metal and wood, it may still improve bond speed and strength but is primarily designed for those difficult plastics.
What types of plastics does this glue NOT bond well?
The glue is not recommended for expanded polystyrene (Styrofoam) or foam rubber. It's also not suitable for fabrics or paper.
How should I store the glue and activator?
Store in a cool, dry place away from direct sunlight. Ensure caps are tightly sealed after each use to maintain efficacy.
Can this adhesive withstand outdoor conditions?
Yes, the cured adhesive is resistant to water, chemicals, and freezing temperatures, making it suitable for many outdoor applications.
What is the shelf life of the Loctite All Plastics Glue and Activator?
When stored correctly, the glue typically has a shelf life of 1-2 years. The activator pen may dry out faster if not sealed properly. Check the packaging for specific expiration dates.
Troubleshooting
Glue is not bonding effectively to plastic.
Ensure you have used the activator pen on at least one of the surfaces. Clean surfaces thoroughly before application and check that the plastic is one of the types listed as compatible (PE, PP, PTFE).
Glue has dried out in the bottle or pen.
If the glue is dried out, it may be old or exposed to air. If the activator pen is dry, the cap may not have been sealed properly. Both would require replacement of the unit.
Bond appears weak after initial setting.
Full cure strength takes up to 24 hours. Avoid stressing the bond during this period. Ensure surfaces were properly prepared and the correct application steps were followed.
Accidental bonding of fingers or surfaces.
Do not pull bonded skin apart. Soak in warm, soapy water. Gently peel or roll skin apart using a blunt edge (like a spoon handle). For surfaces, try soaking in warm, soapy water or using a small amount of acetone (nail polish remover) on a cotton swab, testing in an inconspicuous area first.
Pros and Cons
Pros
- Effectively bonds challenging plastics like PE, PP, and PTFE.
- Fast setting time speeds up repairs.
- Activator ensures a strong bond on low-energy surfaces.
- Dries clear for invisible repairs.
- Resistant to water, chemicals, and freezing temperatures.
- Comes in a convenient 3-pack for multiple uses.
Cons
- Full bond strength develops over time, not instantly.
- Requires careful application to avoid unintended bonding.
- Activator pen may dry out if not stored properly.
- Small volumes (2g glue, 4ml activator) per unit, best for smaller repairs.
Setup, Compatibility & Care Instructions
Setup:
- Ensure both surfaces to be bonded are clean, dry, and free from dust, grease, or oil.
- Apply the activator pen sparingly to one surface. Allow it to dry for a few seconds.
- Apply a small amount of the Loctite All Plastics Glue to the other surface.
- Immediately press the two surfaces together. Hold firmly for several seconds until the bond begins to set.
Compatibility:
This adhesive is specifically designed for difficult-to-bond plastics including Polyethylene (PE), Polypropylene (PP), and PTFE. It also bonds well to rubber, metal, wood, and leather. It is not recommended for use on expanded polystyrene (Styrofoam) or foam rubber, and should not be used on fabrics or paper.
Care:
Store the glue and activator pen in a cool, dry place, away from direct sunlight and extreme temperatures. Ensure the caps are securely fastened after each use to prevent the glue from drying out and the activator from evaporating. Clean any excess glue from the applicator tip immediately after use. Avoid contact with skin and eyes; use in a well-ventilated area.