High Power Instant Grab Interior Adhesive - STORM TRADING GROUP
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later or explore other options below.
Product Information
Full details
This high-strength grab adhesive from STORM TRADING GROUP is designed for indoor DIYers and professionals seeking a faster, cleaner, and mess-free alternative to screws and nails for decorative projects. Its key benefit is an instant, powerful bond that secures items like coving, dado rails, and skirting boards immediately, eliminating the need for drilling or clamps. A potential caveat is that it is specifically formulated for interior use only and may not be suitable for all materials or heavy-duty structural applications.
All features
| Brand | STORM TRADING GROUP |
|---|
Extended Product Information
FAQs
Can this adhesive be used for exterior projects?
No, this adhesive is specifically formulated for interior use only and is not designed to withstand outdoor conditions.
How long does it take to fully cure?
While it provides an instant grab, full curing typically takes 24-48 hours, depending on temperature, humidity, and bead size. Avoid disturbing the bonded items during this period.
Can I paint over the adhesive once it's dry?
Yes, most paints are compatible with the cured adhesive. However, it is recommended to test on a small area first.
What is the shelf life of this adhesive?
When stored correctly in its original, sealed packaging in a cool, dry place, the adhesive typically has a shelf life of 12 months.
How do I clean up spills or excess adhesive?
Wipe away wet adhesive immediately with a damp cloth. Cured adhesive is difficult to remove and may require mechanical means or a specific solvent, depending on the surface.
Is this adhesive suitable for bonding mirrors?
It is not recommended for bonding mirrors directly, as the chemicals in some adhesives can react with mirror backing over time, causing discoloration or damage. Always check the mirror manufacturer's recommendations.
Can I use this on foam or polystyrene?
This adhesive may damage or melt certain types of foam or polystyrene. It is advisable to test on a small, inconspicuous area first or consult the foam manufacturer's guidelines.
Troubleshooting
Adhesive not dispensing
Ensure the nozzle is cut correctly and the cartridge is properly seated in the applicator gun. Check for blockages in the nozzle.
Weak initial bond
Verify that both surfaces are clean, dry, and free from dust or grease. Ensure sufficient adhesive was applied and surfaces were pressed together firmly.
Adhesive oozing out from edges
Apply a controlled bead of adhesive. If necessary, trim any excess immediately with a damp cloth before it cures. Ensure items are not over-pressed.
Difficulty repositioning item
The instant grab nature means repositioning must be done immediately after application. Once the initial bond has set, significant force may be required, potentially damaging the item or surface.
Pros and Cons
Pros
- Eliminates the need for screws and nails for interior decorative items.
- Provides an immediate and strong initial bond, saving time.
- Offers a cleaner and less messy application process.
- Simplifies installation by allowing items to be pressed into place.
- Reduces the risk of damage to surfaces by avoiding drilling.
Cons
- Not suitable for exterior use.
- May not be appropriate for heavy-duty structural applications.
- Requires surfaces to be clean, dry, and free from dust and grease.
- Once bonded, repositioning can be difficult.
Setup, Compatibility & Care
Setup: Ensure surfaces to be bonded are clean, dry, and free from dust, grease, and loose material. For optimal adhesion, surfaces should be sound. Cut the nozzle to the desired bead size. Apply adhesive to one surface in a zig-zag or dotted pattern. For lighter items, press firmly into place immediately. For heavier items, hold in position for a few seconds until the initial grab takes effect.
Compatibility: This adhesive is designed for bonding porous and non-porous interior building materials such as wood, plaster, plasterboard, masonry, concrete, brick, and some plastics. It is not recommended for use on polyethylene, polypropylene, Teflon, or bitumen. Always test on a small, inconspicuous area if unsure.
Care: Store the adhesive in its original container in a cool, dry place, away from direct sunlight and extreme temperatures. Ensure the nozzle is sealed after use to prevent drying. Clean up any excess wet adhesive immediately with a damp cloth. Cured adhesive may be difficult to remove.