Ultrascape Slipbond - Vertical Stone and Brick Slip Adhesive - Instarmac
Not Available
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later or explore other options below.
Product Information
Full details
Instarmac Ultrascape Slipbond is a flexible cladding adhesive for professionals fixing brick slips and natural stone internally and externally. Its key benefit is extended workability, allowing for precise placement on various substrates like render, brick, and block work. A potential caveat is the need for careful substrate preparation to ensure optimal adhesion.
All features
| Brand | Instarmac |
|---|
Extended Product Information
FAQs
Can Ultrascape Slipbond be used for porcelain tiles?
Ultrascape Slipbond is specifically formulated for brick slips and natural stone. For porcelain tiles, a different adhesive from the Instarmac range, such as UltraScape ProFlex SP or similar, would be more appropriate, as they are designed for high-density, low-porosity tiles.
What is the coverage rate of Ultrascape Slipbond?
Coverage varies depending on the trowel size used and the evenness of the substrate. Refer to the product's technical data sheet for specific coverage estimates, typically provided in square meters per bag.
How long does Ultrascape Slipbond need to cure before grouting?
The curing time before grouting typically ranges from 24 to 48 hours, but this can vary based on environmental conditions like temperature and humidity. Always consult the product's technical data sheet for precise recommendations.
Is this adhesive suitable for areas with heavy foot traffic?
While Ultrascape Slipbond provides a strong bond for vertical applications, it is primarily designed for cladding. For floor applications subject to heavy foot traffic, a dedicated heavy-duty floor adhesive would be recommended.
Can I use Ultrascape Slipbond on a damp wall?
No, the substrate must be dry and sound before applying Ultrascape Slipbond. Any dampness will compromise the adhesion and long-term performance of the adhesive.
What is the shelf life of Ultrascape Slipbond?
The product typically has a shelf life of 12 months when stored in original, unopened packaging in a cool, dry condition. Always check the packaging for specific expiry dates.
Troubleshooting
Adhesive not bonding well
Ensure the substrate was properly prepared, clean, and dry. Re-check mixing ratios and application method. Extreme temperatures during application or curing could also affect bonding.
Adhesive setting too quickly
Ensure correct water-to-mix ratio is used. If working in high temperatures, try mixing smaller batches or using cooler water. Check for inadequate substrate preparation which can draw moisture out too fast.
Efflorescence on finished surface
This is often related to soluble salts in the substrate or materials. Ensure materials are stored correctly and consider using a suitable primer or sealant after the adhesive has fully cured if the problem persists.
Cracking of slips/stone after installation
Verify that the substrate has adequate stability and flexibility. Ensure the adhesive was applied correctly and that there is no excessive movement in the structure. This adhesive is designed to be flexible, but extreme movement can still cause issues.
Pros and Cons
Pros
- Excellent adhesion to multiple common building substrates.
- Extended open time allows for easier and more precise tile or slip placement.
- Suitable for external applications, increasing its utility.
- Flexible formulation helps prevent cracking due to movement.
- Can be used in all weather conditions, supporting project timelines.
Cons
- Requires careful preparation of the substrate for optimal performance.
- Not suitable for all types of cladding; specific material compatibility should be checked.
- Drying and setting times can be influenced by environmental conditions.
- Can be more expensive than basic tile adhesives due to its specialized formulation.
Setup, Compatibility & Care
Setup:
- Ensure the substrate is clean, dry, and free from dust, grease, or any loose material. Prime if necessary according to substrate manufacturer recommendations.
- Mix Ultrascape Slipbond with clean water according to the manufacturer's instructions to achieve a smooth, workable paste.
- Apply the adhesive to the substrate using a notched trowel, creating an even bed.
- Press the brick slips or natural stone firmly into the adhesive with a slight twisting motion.
- Use appropriate spacing for grout lines.
Compatibility:
Ultrascape Slipbond is designed for use with:
- Sand/cement render
- Brickwork
- Block work
- Existing concrete
- Tile backer boards (check manufacturer's guidance)
It is suitable for both wall and floor applications, and internal and external use. Always test compatibility with specific stone or slip types if unsure.
Care:
- Protect the applied adhesive from frost and extreme heat during curing.
- Keep the area clean during application.
- Once cured, the adhesive requires no special care beyond normal building maintenance.