Craft Resin Crystal Clear Epoxy Resin Kit - 8L
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later or explore other options below.
Product Information
Full details
This Craft Resin kit is designed for artists and DIY enthusiasts looking to create durable, high-gloss finishes on various projects. Its key benefit is a bubble-free, non-yellowing formula that cures quickly for a professional, glass-like appearance. A potential consideration is the recommended application depth for optimal bubble release.
All features
| Brand | Craft Resin |
|---|
Extended Product Information
FAQs
What is the mixing ratio for Craft Resin?
Craft Resin uses a simple 1:1 ratio by volume for both the resin and the hardener.
How long does it take for Craft Resin to cure?
Craft Resin cures to a hard, scratch-resistant finish in approximately 24 hours. A full cure, where it reaches maximum hardness and heat resistance, may take 3-7 days.
Is Craft Resin safe to use indoors?
Yes, Craft Resin is formulated with minimal odor, is non-toxic, and free of VOCs and solvents, making it safe for use indoors when proper ventilation is still recommended, as with most chemical products.
Can I use Craft Resin for coating a kitchen countertop?
Yes, Craft Resin is food-safe certified and heat resistant up to 203℉ (95℃), making it suitable for coating kitchen countertops and tables, provided the surface is properly prepared and the resin is allowed to fully cure.
What is the maximum pour depth for Craft Resin?
For optimal bubble release and curing, the recommended depth is 1/4 inch. For thicker pours, it is advised to apply in multiple layers.
How should I store unused Craft Resin?
Store Craft Resin in its original, tightly sealed containers in a cool, dry place away from direct sunlight. Ensure both the resin and hardener are stored separately.
Can I add colorants or pigments to Craft Resin?
Yes, Craft Resin is compatible with most epoxy-safe colorants, mica powders, and pigments. It's always recommended to test a small batch first to ensure compatibility and desired color results.
Troubleshooting
Resin remains sticky or soft after 24 hours.
This usually indicates incorrect mixing ratio or insufficient mixing time. Ensure you are using a precise 1:1 ratio by volume and mixing thoroughly for at least 3-5 minutes, scraping all sides of the container. Temperature also plays a role; ensure the ambient temperature is within the recommended range (typically 70-80°F or 21-27°C).
Excessive bubbles in the cured resin.
Ensure the resin and hardener were warmed slightly before mixing (e.g., by placing sealed containers in warm water). Pour the resin gently and avoid over-mixing. Applying at the recommended 1/4 inch depth helps bubbles escape. A torch or heat gun can be used carefully to pop surface bubbles just after pouring.
Resin turned yellow.
While Craft Resin is formulated to resist yellowing, prolonged exposure to UV light (direct sunlight) can accelerate this process over time. Ensure finished pieces are not left in direct sunlight for extended periods. This is more of a long-term degradation than a curing issue.
Surface imperfections or waves.
Ensure the surface you are pouring onto is perfectly level. Use a spirit level to check. Unevenness will cause the resin to pool in some areas and leave others thin, leading to an uneven finish. Adjust the item being poured on until it is level.
Pros and Cons
Pros
- Produces a crystal-clear, glossy finish.
- Resistant to yellowing, maintaining clarity over time.
- Fast 24-hour curing time.
- Food-safe and low VOCs make it suitable for a wider range of projects.
- Comes with all necessary accessories to get started.
- Good heat resistance for durable surfaces.
Cons
- Optimal bubble release is achieved when resin is warm and applied at a recommended depth of 1/4 inch.
- Requires careful measurement and mixing for best results.
- Can be sensitive to temperature and humidity during curing.
Setup, Compatibility & Care
Setup:
- Ensure your workspace is well-ventilated, clean, and level. Protect surfaces with plastic sheeting or paper.
- Wear the provided gloves to protect your skin.
- Measure the resin and hardener accurately using the 1:1 ratio by volume. Use separate, clean containers for measuring.
- Pour the hardener into the resin or vice-versa. Mix thoroughly with the provided stick, scraping the sides and bottom of the container, for at least 3-5 minutes.
- Allow the mixed resin to sit for a few minutes to help bubbles rise before pouring. Gentle warming of the resin and hardener before mixing can also aid bubble release.
- Pour the mixed resin onto your project, ensuring it is spread evenly. For larger pours, consider applying in layers no thicker than 1/4 inch at a time, allowing each layer to partially cure before adding the next.
Compatibility:
- Craft Resin is compatible with most common art materials, including pigments, mica powders, alcohol inks, and dried flowers. Always test with a small amount first.
- It adheres well to sealed wood, finished concrete, most plastics, silicone molds, and painted surfaces.
- Ensure surfaces are clean, dry, and free from dust or grease.
Care:
- Clean uncured resin spills immediately with a cloth dampened with isopropyl alcohol.
- Once cured, clean surfaces with a mild soap and water. Avoid abrasive cleaners that could scratch the finish.
- Protect from prolonged direct sunlight, which can cause yellowing over extended periods, though the formula is highly resistant.