Q.Max Sheet Metal Punch - 5/8 in
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later or explore other options below.
Product Information
Full details
This Q.Max Sheet Metal Punch is designed for professionals and DIYers needing to create clean, precise 5/8 inch imperial sized holes in sheet metal up to 16 gauge. Its key benefit is producing burr-free holes that require no additional finishing, saving time and effort. A potential caveat is that a separate hexagonal wrench must be ordered for operation.
All features
| Model Part Number | Qma58 |
|---|---|
| Brand | Q.Max |
Extended Product Information
FAQs
What is the maximum thickness of sheet metal this punch can cut?
This punch is designed for sheet metal up to 16 gauge in thickness.
Do I need to drill a hole before using the punch?
Yes, you need to drill a pilot hole large enough for the hexagonal screw to pass through before using the punch.
What tool is needed to operate the punch?
A 7/32 inch hexagonal wrench is required to tighten the screw and actuate the punch. This must be ordered separately.
Does the punch create a finished hole, or will it need deburring?
The Q.Max Sheet Metal Punch is designed to produce a burr-free hole that requires no extra finishing.
What is the diameter of the hole created by this punch?
This specific model creates a 5/8 inch diameter hole.
How do I prevent rust on the punch?
Clean the punch after use and apply a light coat of oil to the cutting edges and threads, especially for storage. The black anti-corrosive finish helps, but maintenance is recommended.
Can this punch be used on materials other than sheet metal?
This punch is specifically designed for cutting clean holes in sheet metal up to 16 gauge. Its performance on other materials is not guaranteed.
Troubleshooting
Punch is not cutting cleanly
Ensure the sheet metal is within the 16-gauge limit. Check that the hexagonal screw is being tightened sufficiently with the correct wrench. Inspect the cutting edges for dullness or damage.
Difficulty threading the die nut or screw
Verify that the pilot hole is the correct size and that there are no burrs around the hole that could impede threading. Ensure the threads on the screw and die nut are clean and free from debris.
Punch is stuck after cutting
Carefully attempt to unscrew the hexagonal screw. If still stuck, gently tap the punch body with a soft mallet. Ensure the material was not significantly thicker than 16 gauge.
Surface finish is damaged
This is likely cosmetic and does not affect performance. Clean the tool and apply oil to prevent further corrosion. For operational damage, inspect cutting edges.
Pros and Cons
Pros
- Creates clean, burr-free holes in sheet metal.
- Saves time by eliminating the need for finishing.
- Durable, heat-treated cutting edges ensure longevity.
- Even load design provides consistent cutting performance.
- Designed for up to 16-gauge sheet metal.
Cons
- Requires a separate purchase of the hexagonal wrench.
- Limited to a specific 5/8 inch hole size.
- Designed for imperial sizing only.
- Requires a pilot hole to be drilled for insertion.
- Suitable for sheet metal up to 16 gauge, not thicker materials.
Setup, Compatibility & Care
Setup:
- Drill a pilot hole in the sheet metal large enough to clear the hexagonal screw of the punch.
- Thread the Die and hexagonal screw through the pilot hole from one side.
- Screw the die nut onto the hexagonal screw from the other side of the sheet metal.
- Using a 7/32 inch hexagonal wrench (ordered separately), tighten the hexagonal screw. As the screw tightens, the punch will cut cleanly through the metal.
Compatibility:
- Suitable for sheet metal up to 16 gauge thickness.
- Requires a 7/32 inch hexagonal wrench for operation.
Care:
- After use, clean the punch and die of any metal debris.
- Apply a light coat of oil to the cutting edges and threaded parts to prevent rust, especially during storage.
- Store the punch in its original box or a dry location to protect the anti-corrosive finish.