PVC Bathroom Wall Panel - Gloss Grey Marble Effect
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later or explore other options below.
Product Information
Full details
This PVC bathroom wall panel is designed for homeowners seeking a quick, durable, and stylish upgrade to their showering spaces, wet rooms, and bathroom walls. Its key benefit is providing a waterproof, low-maintenance, and modern grey marble effect finish that enhances brightness and offers long-lasting surface protection. A potential caveat is the need for precise cutting and fitting to ensure a seamless, waterproof seal.
All features
| Brand | B&Q |
|---|
Extended Product Information
FAQs
Are these panels suitable for a ceiling installation?
While primarily designed for walls, they can be used on ceilings in wet areas if properly supported and adhered, provided all edges are sealed and appropriate fixings are used.
Can I install these panels over existing tiles?
Yes, provided the existing tiles are securely fixed, the grout lines are not too deep, and the surface is clean and dry. You may need to use a stronger adhesive or consider preparing the surface first.
How do I cut the panels for corners or around pipes?
Use a sharp utility knife or a fine-toothed saw for straight cuts. For curves or holes, a jigsaw can be used. Always measure carefully and mark your cuts before proceeding. Smooth any rough edges after cutting.
What is the expected lifespan of these panels?
When installed correctly and maintained properly, these PVC panels offer a long lifespan, typically lasting many years due to their durable and waterproof nature.
Can I paint these panels?
These panels are designed with a specific finish and are not intended to be painted. Painting could compromise the waterproof integrity and the finish may not adhere well.
What kind of sealant should I use?
Use a 100% silicone sealant specifically designed for bathroom and kitchen use. Ensure it is anti-fungal and suitable for use with plastics or PVC.
How do I clean mould or mildew if it appears?
While the panels are resistant to mould, any accumulation can usually be removed with a soft cloth and mild detergent. For stubborn spots, a diluted solution of white vinegar or a specialised bathroom cleaner (non-abrasive) can be used, followed by rinsing with water.
Troubleshooting
Panels not adhering properly
Ensure the wall surface is clean, dry, and free from dust or grease. Use the correct type and amount of adhesive as recommended by the manufacturer. Allow adequate curing time for the adhesive.
Visible gaps between panels
Ensure panels are cut precisely and installed tightly together. Use appropriate trims to cover any minor gaps. Check that the wall surface is flat and not causing unevenness during installation.
Water ingress around fixtures or edges
Re-seal all edges, corners, and penetrations with a high-quality, bathroom-grade silicone sealant. Ensure sealant is applied smoothly and continuously.
Scratched or dull finish
Avoid using abrasive cleaning materials. Clean gently with a soft cloth and mild soap. Minor scratches may be buffed out with a plastic polish designed for automotive or marine applications, but test in an inconspicuous area first.
Pros and Cons
Pros
- Provides a completely waterproof solution for wet areas.
- Offers a modern, attractive aesthetic with a realistic marble effect.
- Requires minimal maintenance compared to grout and tile.
- Durable surface resists scratches and impact.
- Can be installed relatively quickly, reducing project time.
Cons
- Requires careful cutting and fitting to ensure water integrity.
- May not provide the same perceived value or texture as natural stone.
- Can be susceptible to damage from very sharp objects.
- Adhesive selection and application are critical for longevity.
- Specific cleaning products should be avoided to maintain the gloss finish.
Setup, Compatibility & Care
Setup:
- Ensure walls are clean, dry, and structurally sound before installation.
- Measure and cut panels accurately using a fine-toothed saw or utility knife. Always measure twice, cut once.
- Apply a suitable waterproof adhesive designed for PVC panels to the wall or the back of the panel, following the adhesive manufacturer's instructions.
- Press panels firmly into place, ensuring a tight fit against adjacent panels and surfaces. Use a spirit level to ensure vertical and horizontal alignment.
- Use appropriate trims and sealants (e.g., silicone sealant) around edges, corners, and any cut-outs (like for pipes or shower fixtures) to maintain a fully waterproof finish.
Compatibility:
- Suitable for installation over existing tile backer boards, plasterboard, or directly onto sound, dry masonry walls (ensure walls are free of damp).
- Requires compatible trims for internal and external corners, and end-capping.
- Ensure adequate ventilation in the bathroom to prevent condensation build-up, even with waterproof surfaces.
Care:
- Clean regularly with a soft, damp cloth and mild detergent.
- Avoid abrasive cleaners, scouring pads, or harsh chemicals, as these can scratch or damage the gloss finish.
- Wipe away soap scum and water spots promptly to maintain the pristine appearance.