WAGO Micro Push Wire Connector - 243-808
Not Available
Not Available
Not Available
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later or explore other options below.
Product Information
Full details
The WAGO 243-808 Micro Push Wire Connector is designed for electricians and DIY enthusiasts working with solid conductors of small diameters (0.6 mm to 0.8 mm) in low-power applications. Its primary benefit is a compact, tool-free connection that simplifies wiring in confined spaces like junction boxes. A key consideration is its limitation to solid core wires and a maximum voltage of 100V, making it unsuitable for high-power or flexible wire applications. This connector offers 8 clamp positions and a secure connection via chrome-nickel spring steel clamps, with built-in marking capabilities.
All features
| Model Part Number | 243-808 |
|---|---|
| Brand | WAGO |
Extended Product Information
FAQs
Can I use stranded wires with the WAGO 243-808?
No, the WAGO 243-808 is specifically designed for solid core wires only. Using stranded or flexible wires will result in an insecure connection and potential failure.
What is the maximum wire size this connector can handle?
This connector is designed for solid conductors with diameters ranging from 0.6 mm to 0.8 mm.
What is the maximum voltage and current rating for this connector?
The nominal voltage is 100V and the nominal current is 6A.
How do I know if the wire is properly connected?
When the wire is correctly inserted, it will feel firmly seated with a slight resistance, indicating it has engaged with the internal clamp. A gentle tug should confirm a secure connection.
Can this connector be used in outdoor or wet environments?
The WAGO 243-808 is intended for indoor use, typically within junction boxes or control cabinets. It is not rated for outdoor or wet environments.
How many wires can be connected to one WAGO 243-808 unit?
This model features 8 clamp positions, allowing for the connection of up to 8 individual solid conductors.
Can I remove and re-use the connector?
Yes, wires can be removed by firmly pulling them out of the connector. The connector can then be re-used for new connections.
Troubleshooting
Wire does not insert easily or completely.
Ensure the wire is solid core and within the 0.6 mm to 0.8 mm diameter range. Check that the wire end is stripped cleanly and is not bent or damaged. Ensure no insulation is present inside the connection point.
Connection feels loose or intermittent.
Remove the wire and re-insert, ensuring it is pushed in fully until it seats properly. Verify the wire diameter is correct. Inspect the wire for any damage that might prevent a secure grip.
Connector does not fit into the intended space.
Verify the dimensions of the WAGO 243-808 (18.4 mm width, 10 mm depth, 6.8 mm height) against the available space. Consider alternative WAGO connectors if a smaller size is required.
Connector is overheating.
Ensure the connected wire is within the specified gauge and that the current draw does not exceed the 6A rating. Check that all connections are secure and that there are no signs of arcing. If the issue persists, disconnect power immediately and investigate the circuit load.
Pros and Cons
Pros
- Streamlines wiring in confined spaces with its compact design.
- Tool-free push-wire connection saves installation time.
- Secure and reliable connection for solid conductors.
- Offers flexibility for mounting on various surfaces.
- Integrated marking capabilities enhance project organization.
Cons
- Limited to solid core wires only; not suitable for stranded or flexible wires.
- Maximum voltage rating of 100V restricts use to low-power applications.
- Small conductor size range (0.6-0.8 mm) may not suit all projects.
- Requires careful insertion to ensure a proper connection for small wires.
Setup, Compatibility & Care
Setup:
- Ensure the power is off before beginning any wiring.
- Strip the solid conductor wires to the appropriate length, ensuring they are clean and free of damage. The WAGO 243-808 is designed for solid conductors between 0.6 mm and 0.8 mm in diameter.
- Simply push the stripped end of the solid wire into one of the available clamp positions until it is firmly seated. A slight resistance followed by a solid click indicates a secure connection.
- Repeat for all conductors.
- The connector can be mounted onto a carrier rail or adhered to a smooth surface using appropriate mounting accessories (sold separately).
Compatibility:
- Wire Type: Compatible exclusively with solid core wires.
- Wire Diameter: Suitable for solid conductors ranging from 0.6 mm to 0.8 mm.
- Voltage/Current: Designed for applications up to 100V and 6A.
- Environment: Ideal for low-power, internal connections, commonly found in junction boxes and control cabinets.
Care:
These connectors are maintenance-free once installed. They are designed for a long service life under normal operating conditions. Avoid exposing the connectors to excessive moisture, extreme temperatures, or corrosive substances. If cleaning around the installed connectors is necessary, use a dry or slightly damp cloth, ensuring no liquid enters the connection points.