Deluxe Materials Roket Ca Gel - 3g
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later or explore other options below.
Product Information
Full details
The Deluxe Materials Roket Ca Gel is designed for modelers and hobbyists needing a strong, fast-acting adhesive for various materials. Its primary benefit is a rapid 10-second bond that also fills small gaps, simplifying assembly. A potential caveat is its gel consistency, which may require careful application to avoid excess on delicate parts.
All features
| Model Part Number | AD-90 |
|---|---|
| Brand | DELUXE MATERIALS |
Extended Product Information
FAQs
How long does the bond take to fully cure?
While the initial bond is achieved in about 10 seconds, full cure, reaching maximum strength, can take up to 24 hours depending on humidity and temperature.
Can I use this on clear plastic parts?
Yes, but apply with extreme caution. Excess gel can fog or craze clear plastics. Apply very sparingly and avoid contact with the clear surface if possible.
What is the shelf life of Roket Ca Gel?
When stored correctly in a cool, dry place with the cap tightly sealed, the adhesive typically remains effective for at least one year.
How do I remove excess uncured gel?
Wipe away uncured gel immediately with a clean, dry cloth. For stubborn uncured residue, a specialized CA debonder can be used carefully.
Is this adhesive flexible once cured?
No, Roket Ca Gel creates a rigid bond. It is not suitable for applications requiring flexibility or materials that will be repeatedly bent.
Can I sand this adhesive after it has cured?
Yes, once fully cured, the adhesive can be sanded. However, it is a very hard material, so use appropriate grit sandpaper and caution.
Troubleshooting
Adhesive not bonding quickly
Ensure surfaces are clean and free of contaminants. Check if the adhesive is expired or has been exposed to moisture. For slower cures on certain materials, a CA accelerator might be needed.
Gel is too thick or difficult to dispense
Store the tube at room temperature for a short period. If the nozzle is blocked, carefully clear it with a pin or a fine wire.
Adhesive bonded to wrong parts
Attempt to carefully separate the parts while the adhesive is still fresh or slightly flexible. For fully cured bonds, gentle prying, sanding, or the use of a CA debonder might be necessary, though this may damage delicate surfaces.
Fumes are irritating
Work in a well-ventilated area or use a fan to direct fumes away from your breathing zone. Consider using a respirator if working in an enclosed space for extended periods.
Pros and Cons
Pros
- Extremely fast bonding time for quick assembly.
- Gel formula is excellent for gap filling and prevents dripping.
- Strong bond suitable for plastics, wood, metal, and rubber.
- User-friendly packaging for controlled application.
- Long shelf life when stored correctly.
Cons
- Gel can be difficult to remove if applied to unintended areas.
- Bond is permanent; requires precise placement on the first try.
- May not be suitable for very flexible materials that require some movement.
- Fumes can be irritating; good ventilation is recommended.
Setup, Compatibility & Care
Setup: No specific setup is required. Ensure the surfaces to be bonded are clean, dry, and free from dust or grease for optimal adhesion. Apply a small amount of gel to one surface and press the parts together firmly, holding for approximately 10-20 seconds until the bond is secure.
Compatibility: This adhesive is compatible with most hard plastics, wood, metal, and synthetic rubber. Avoid using on soft plastics like polyethylene or polypropylene, as CA adhesives can damage or fail to bond with these materials. It is also not recommended for Styrofoam or foam surfaces without a specific foam-safe accelerator.
Care: Store the tube in a cool, dry place, away from direct sunlight. Ensure the cap is tightly sealed after each use to prevent the adhesive from drying out in the tube. Clean any excess uncured adhesive immediately with a dry cloth or a specialized CA debonder. Cured adhesive can be carefully scraped or sanded away.