Permatex Plastic Weld High Strength Epoxy Plastic Glue Repair - Cream
Not Available
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later or explore other options below.
Product Information
Full details
This Permatex Plastic Weld High Strength Epoxy is designed for general-purpose bonding of various materials like hard and soft plastics to specified surfaces, offering a tough, durable bond that cures quickly. It's ideal for users needing a strong, reliable plastic adhesive for repairs, but it's important to note that it will not bond most polyethylene or polypropylene plastics.
All features
| Colour | Cream |
|---|---|
| Brand | Permatex |
Extended Product Information
FAQs
What types of plastic can Permatex Plastic Weld bond?
It bonds hard and soft plastics, as well as composites, ceramics, and wood. However, it will not bond most polyethylene or polypropylene plastics.
How long does it take for the epoxy to fully cure?
Usable strength is reached in approximately 4 hours at 72°F (22°C). Full cure and maximum strength may take longer.
Can this product be used for outdoor repairs?
Yes, it is water and chemical resistant, and offers a wide temperature range (-51°C to 121°C), making it suitable for many outdoor applications.
What is the maximum gap I can fill with this adhesive?
This epoxy can fill gaps up to 0.125 inches.
Do I need to use a primer before applying this epoxy?
No, Permatex Plastic Weld requires no primers for most applications.
How should I store the unused product?
After use, attach the nozzle cap securely and store the syringe in its molded tray in a cool, dry place.
What is the bond strength of this product?
It provides permanent strength up to 3500 PSI.
Troubleshooting
Adhesive is not dispensing properly.
Ensure the plunger is moving freely and that the nozzle is not blocked. Check that equal amounts of resin and hardener are being pushed out.
Bond is weak or failing.
Verify that surfaces were clean, dry, and properly roughened. Ensure thorough mixing of resin and hardener for the full two minutes. Confirm the materials being bonded are compatible (not polyethylene or polypropylene).
Adhesive is setting too quickly or too slowly.
Ambient temperature can affect cure time. Ensure application occurs within the recommended temperature range. For slower cures, cooler temperatures might be needed; for faster, slightly warmer conditions (within reason) may help.
Excessive uncured adhesive on surfaces.
Wipe away excess immediately after assembly using a disposable cloth. If it has started to set, careful scraping may be possible once it has achieved initial hardness.
Pros and Cons
Pros
- Forms a very strong and permanent bond.
- Fast curing time speeds up repair processes.
- Versatile for bonding a variety of materials beyond just plastics.
- Good resistance to water and chemicals for lasting repairs.
- User-friendly application with no need for primers.
Cons
- Will not bond polyethylene or polypropylene plastics.
- Requires careful mixing for optimal results.
- Gap filling is limited to 0.125 inches.
Setup, Compatibility & Care
Preparation: Ensure the work area is protected from spills. Surfaces to be bonded must be clean, dry, and free of grease or oil. Roughen smooth surfaces using sandpaper or an abrasive to improve adhesion.
Mixing and Application:
- Remove the syringe cap.
- Turn the syringe nozzle end up and pull the plunger back slightly (1/8") to allow air bubbles to rise. Snap off and save the storage cap.
- Push the plunger to dispense equal amounts of hardener and resin onto a disposable surface like cardboard. The mixing paddle will emerge from the plunger.
- Pull back the plunger to stop the flow. Snap the cap back on the syringe.
- Thoroughly mix the dispensed adhesive with the provided paddle for two minutes until it achieves an even color.
- Apply a small amount of the mixture to both surfaces and assemble the parts immediately. Excess epoxy should be removed right away.
Cure Time: Usable strength is reached in approximately 4 hours at 72°F (22°C). Cooler temperatures may extend the set time.
Storage: Attach the nozzle cap and store the syringe in its molded tray.
Compatibility: Bonds hard and soft plastics, composites, ceramics, and wood. Does NOT bond most polyethylene or polypropylene plastics.
Care: Once cured, the bond is water and chemical resistant. Clean spills immediately with a disposable cloth before the epoxy sets.