PTFE Dry Film Lubricant - 400mL
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later or explore other options below.
Product Information
Full details
This PTFE Dry Film Lubricant from Aerosol Solutions is designed for individuals and industries requiring a durable, non-sticky, and moisture-repelling lubricant. Its key benefit is providing a smooth finish suitable for mechanisms where conventional oils and greases attract dust or dry out. A potential caveat is its specific formulation for dry film application, which may not suit all extreme-pressure or high-load scenarios.
All features
| Model Part Number | ASO0205 |
|---|---|
| Brand | Aerosol Solutions |
Extended Product Information
FAQs
What is PTFE dry film lubricant used for?
It's used for lubricating mechanisms where a dry, non-sticky, moisture-repellent, and durable surface is needed, especially in dusty environments or where conventional oils and greases would attract dirt or dry out.
How long does the lubrication last?
The duration depends on the application's wear rate and environmental conditions. For most typical uses, it provides long-lasting lubrication, but reapplication may be needed for very high-wear or continuous operational scenarios.
Can I use this on plastic parts?
It is generally compatible with many plastics, but it is always recommended to test on a small, inconspicuous area first to ensure no adverse reactions occur before full application.
Is this product suitable for high-temperature applications?
PTFE has a high-temperature resistance, but the overall performance of the lubricant in high heat will depend on the specific conditions and the substrate it is applied to. It is best suited for moderate temperature ranges where conventional lubricants fail due to drying out.
How should I clean off the dry film lubricant if needed?
The dry film can typically be removed using a suitable solvent or degreaser, followed by wiping the surface clean.
Does it provide corrosion protection?
Yes, the dry film formula repels moisture, which helps to protect the treated surface from corrosion.
What is the difference between this and a wet lubricant?
Unlike wet lubricants (oils/greases), this PTFE dry film lubricant leaves a non-sticky coating that doesn't attract dust and dirt, making it ideal for cleaner applications.
Troubleshooting
Uneven spray pattern or clogging
Shake the can vigorously for at least two minutes before use and periodically during application. Ensure the nozzle is not blocked. If clogged, remove the nozzle and soak in a suitable solvent, then clear with a fine pin before reattaching.
Lubricant appears wet or sticky after application
Ensure the can was shaken sufficiently and applied in a thin, even coat. Allow more drying time in cooler or more humid conditions. Avoid over-application.
Poor adhesion or premature wear
Verify that the surface was properly prepared (clean, dry, and degreased) before application. Reapply after thorough cleaning of the surface.
Difficulty spraying
Check that the nozzle is properly attached and clear. Ensure the can is upright and the propellant is sufficient. If the can is cold, warm it slightly by immersion in warm water (not hot).
Pros and Cons
Pros
- Repels moisture effectively, offering corrosion protection.
- Dry, non-sticky film prevents dust and dirt accumulation.
- Provides a durable, smooth finish on various mechanisms.
- Suitable alternative to oils and greases in dusty environments.
- Maintains performance where conventional lubricants may dry out.
Cons
- Not designed for extreme pressure or heavy load applications.
- May require reapplication for very high-wear or long-term continuous use.
- Specific use cases where traditional wet lubricants are preferred might not benefit.
- Requires proper surface preparation for optimal adhesion.
- Ventilation is necessary during application.
Setup, Compatibility & Care
Setup:
- Ensure the surface to be treated is clean, dry, and free from grease, oil, and loose debris. For best results, degrease and wipe the surface.
- Shake the can thoroughly for at least two minutes before use and periodically during application.
- Hold the can upright, approximately 15-20 cm (6-8 inches) from the surface.
- Apply a thin, even coat. Avoid over-application.
- Allow the lubricant to dry completely. Drying time will vary depending on temperature and humidity, but typically takes 5-10 minutes, forming a dry film.
Compatibility:
This lubricant is compatible with most metals and many plastics. However, it is recommended to test on a small, inconspicuous area first, especially with delicate plastics or painted surfaces, to ensure no adverse reaction occurs. It is not recommended for use on electrical contacts where conductivity is required.
Care:
Store the can in a cool, dry place away from direct sunlight and heat sources. Keep the nozzle clean by inverting the can after each use and spraying for a short burst until clear propellant emerges.