Clarke International Spray Gun - Pgf14 - 1.4Mm
Not Available
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later or explore other options below.
Product Information
Full details
The Clarke PGF14 is a professional-grade gravity-fed spray gun for auto refinishing and manufacturing. It offers excellent atomization and application speed with its 1.4mm nozzle and 600ml cup, but requires a minimum 3HP air compressor for optimal performance. Key features include precise control over spray pattern and paint volume, making it versatile for automotive, woodworking, and general workshop tasks.
All features
| Model Part Number | PTDCLA3090090 |
|---|---|
| Brand | Clarke International |
Extended Product Information
FAQs
What is the recommended air pressure for the Clarke PGF14?
While specific PSI can vary with coating and application, a general starting point is between 30-50 PSI. Always consult the product manual for precise recommendations and adjust based on your specific needs and coating.
What type of coatings can be used with this spray gun?
The PGF14 is suitable for a wide range of automotive and industrial coatings, including primers, base coats, clear coats, lacquers, and enamels. Ensure the coating's viscosity is appropriate for the 1.4mm nozzle and follow manufacturer thinning recommendations.
How often should the nozzle and air cap be cleaned?
For best performance and longevity, the nozzle and air cap should be thoroughly cleaned immediately after each use. Regular maintenance cleaning is crucial to prevent clogs and ensure consistent spray patterns.
Can I use this spray gun with a smaller air compressor?
The spray gun requires a minimum of a 3HP air compressor with an average air consumption of 11 CFM for efficient operation. Using a smaller compressor may result in poor atomization and inconsistent spray patterns.
What is the capacity of the gravity cup?
The Clarke PGF14 comes equipped with a 600ml nylon gravity cup.
Is this spray gun suitable for DIY use?
While it can be used for DIY projects, the PGF14 is designed as a professional-grade tool. Its performance is optimized for trade applications, and it requires a suitable air compressor. Users new to spray painting may benefit from practicing on scrap material first.
Troubleshooting
Uneven spray pattern or "fishtails"
Ensure the air cap is correctly aligned and tightened. Check for blockages in the nozzle or air passages. Adjust air pressure and fluid flow. Ensure the coating is properly thinned.
Poor atomization or "cobwebbing"
Increase air pressure slightly. Ensure the nozzle and air cap are clean and undamaged. Verify the coating viscosity is within the recommended range.
Paint leaking from the cup or connections
Check that the cup is securely fastened. Inspect seals and O-rings for damage and replace if necessary. Ensure all connections are tight.
Gun not spraying or sputtering
Check for blockages in the fluid needle, nozzle, or cup filter. Ensure the air supply is adequate and consistent. Prime the gun by holding a rag over the nozzle and briefly opening the air valve to draw paint up.
Pros and Cons
Pros
- Delivers excellent atomization for professional finishes.
- Precise control over spray pattern and paint volume.
- Large 600ml gravity cup reduces the need for frequent refills.
- Suitable for a wide range of professional spraying tasks.
- Robust design for durability in demanding environments.
Cons
- Requires a minimum 3HP air compressor, adding to initial setup cost.
- Average air consumption of 11cfm may be high for smaller compressors.
- Primarily designed for professional use, may be complex for beginners.
Setup, Compatibility & Care
Setup:
- Connect the spray gun to an air compressor capable of delivering at least 3HP and a consistent 11 CFM (Cubic Feet per Minute) of air at the required PSI (typically 30-50 PSI, check manual for specifics).
- Ensure the 600ml nylon gravity cup is securely attached and filled with your chosen coating.
- Adjust the spray pattern control for the desired fan shape (round to fan).
- Adjust the paint volume control to regulate the flow of material.
Compatibility:
- Requires an air compressor with a minimum of 3HP and 11 CFM capacity.
- Compatible with most standard automotive and industrial coatings (check coating viscosity recommendations).
Care:
- Immediate Cleaning: After each use, thoroughly clean the nozzle, air cap, and cup with the appropriate solvent (e.g., thinner for solvent-based paints, water for water-based paints).
- Disassembly: Partially disassemble the gun according to the manual for deeper cleaning of internal passages.
- Storage: Store in a clean, dry place, away from extreme temperatures.