Mehr Power Mix 2K Repair Adhesive - Clear - Pack of 2 Kits
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later or explore other options below.
Product Information
Full details
The Mehr Power Mix 2K Repair Adhesive is designed for DIY enthusiasts and professionals needing a strong, clear bond for plastic and metal components. Its key benefit is a rapid 5-minute work time for quick repairs, though achieving a full structural cure requires 24 hours. This kit contains two 50ml cartridges of a two-part epoxy adhesive that mixes and dispenses uniformly for reliable results.
All features
| Colour | White |
|---|---|
| Model Part Number | VIP25C |
| Brand | Mehr |
Extended Product Information
FAQs
What is the shelf life of this adhesive?
Unopened cartridges should be stored in a cool, dry place. Refer to the product packaging for specific expiration dates, but generally, they remain viable for at least one year when stored correctly.
Do I need a special gun to use this?
Yes, this is a two-part (2K) adhesive that requires a specific 2K cartridge applicator gun designed for 50ml cartridges. This is typically sold separately.
Can this adhesive be used outdoors?
Yes, once fully cured, the adhesive forms a durable bond that is suitable for outdoor applications, provided the bonded materials themselves can withstand environmental exposure.
What is the difference between the 5-minute cure and the 24-hour cure?
The 5-minute cure refers to the 'work life' or 'set time' – the period during which you can position the parts. The 24-hour cure is the 'full cure' time, after which the adhesive reaches its maximum strength and durability.
How do I clean up uncured adhesive?
Uncured adhesive can usually be wiped away with a cloth dampened with a solvent like acetone or isopropyl alcohol. Always test the solvent on an inconspicuous area first.
Can I paint over the cured adhesive?
Generally, yes. Once fully cured, the adhesive can often be sanded and painted, though compatibility with specific paint types should be tested.
Is this adhesive suitable for high-temperature applications?
While the adhesive forms a strong bond, its specific temperature resistance should be checked against the requirements of your application. It is generally suitable for typical room temperature and moderate heat exposure.
Troubleshooting
Adhesive is not curing or curing slowly.
Ensure both parts of the adhesive were dispensed and mixed in the correct ratio. Verify that the temperature is within the recommended range for curing. Older adhesive may lose potency.
Poor bond strength.
Surfaces may not have been properly cleaned and prepared. Ensure all grease, oil, and dirt were removed. Check that the adhesive was mixed thoroughly and allowed to cure for the full 24 hours.
Dispensing issues from the applicator gun.
Check that the cartridges are properly seated in the applicator gun and that the dispensing mechanism is functioning correctly. Ensure any mixing nozzle is not clogged.
Adhesive is cloudy or discolored after curing.
This can sometimes occur if the adhesive was exposed to excessive heat during curing or if the mixing was incomplete. Ensure proper ventilation and avoid curing in direct sunlight if discoloration is a concern.
Pros and Cons
Pros
- Fast initial set time for convenience.
- Creates a very strong and durable bond once fully cured.
- Clear adhesive is visually unobtrusive.
- Suitable for bonding dissimilar materials like plastic and metal.
- Comes in a convenient twin-pack.
Cons
- Requires a specific applicator gun for the 2K cartridges (not included).
- Full strength is not achieved for 24 hours.
- Requires careful mixing of the two parts for optimal performance.
- Limited work time once mixed, demanding prompt application.
Setup, Compatibility & Care
Setup: This product requires a 2K (two-part) cartridge applicator gun, which is sold separately. Ensure the gun is compatible with the 50ml cartridge size. Insert the cartridges into the gun and engage the plunger mechanism. Before initial use, dispense a small amount to ensure both parts are flowing evenly. Mix the two components thoroughly by applying the adhesive to a disposable surface or using the included mixing nozzle (if applicable to your dispenser setup).
Compatibility: The adhesive is designed for bonding most plastics and metals. Test on an inconspicuous area first if unsure about material compatibility. Avoid use on materials that may be sensitive to epoxy resins.
Care: Store unused cartridges in their original packaging in a cool, dry place, away from direct sunlight. Ensure the tips are sealed to prevent premature curing. Once mixed, the adhesive has a limited pot life and should be used immediately. Clean up any excess uncured adhesive with a suitable solvent as recommended by the applicator gun manufacturer, and wipe away cured adhesive mechanically.