E6000 Craft Glue - 59.1Ml - Clear
Not Available
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later or explore other options below.
Product Information
Full details
The E6000 Craft Glue (59.1ml Tube, Clear) is designed for crafters, DIY enthusiasts, and professionals seeking an exceptionally strong and versatile adhesive. Its key benefit is its ability to form permanent bonds on a wide array of difficult materials, including many plastics, while also adhering reliably to common surfaces. A potential caveat is its longer cure time compared to some other adhesives, requiring patience for optimal bond strength.
All features
| Model Part Number | E6000 PREMIUM |
|---|---|
| Brand | E6000 |
Extended Product Information
FAQs
How long does E6000 Premium take to fully cure?
Full cure typically takes 72 hours, although handling time is usually achieved within 24 hours. Optimal strength develops over several days.
Is E6000 Premium waterproof once cured?
Yes, E6000 Premium is waterproof after it has fully cured, making it suitable for applications exposed to moisture.
Can I use E6000 Premium on fabrics?
Yes, E6000 Premium bonds well to most fabrics, creating a durable and flexible bond suitable for crafts and repairs.
Will E6000 Premium damage clear plastics?
E6000 Premium is designed for use on many plastics, including clear ones like acrylic. However, always test on an inconspicuous area first to confirm compatibility and prevent clouding.
Can E6000 Premium be painted over?
Yes, E6000 Premium dries to a clear finish that can be painted over once fully cured.
What is the best way to clean up uncured E6000 Premium?
Uncured adhesive can be cleaned up using mineral spirits or denatured alcohol. For dried adhesive, removal can be more difficult and may require scraping or soaking with solvent.
Does E6000 Premium have a strong odor?
E6000 Premium has a characteristic industrial odor during application. It is recommended to use it in a well-ventilated area.
Troubleshooting
Adhesive not dispensing
Ensure the cap is fully removed. If clogged, carefully puncture the seal inside the nozzle with a pin or paperclip. Store upright to prevent the tip from sealing.
Slow or incomplete curing
Ensure adequate ventilation and appropriate temperature (ideally between 50-90°F or 10-32°C). Curing time can be longer in humid or cold conditions. Ensure surfaces were completely dry before application.
Adhesive remains tacky after 24 hours
This may indicate insufficient ventilation, low temperatures, or excessive application thickness. Ensure proper application conditions and allow more time. For very thick applications, consider applying in thinner layers if possible.
Poor adhesion to plastic
Ensure the plastic surface is clean and free of mold release agents or oils. Lightly scuffing the surface with fine-grit sandpaper can improve adhesion on very smooth plastics. Always test compatibility on a small area first.
Pros and Cons
Pros
- Superior adhesion to a wide range of plastics, including 3D printed materials.
- Bonds to virtually any material, offering extreme versatility.
- Creates durable, long-lasting, and waterproof bonds.
- Remains flexible after curing, reducing the risk of breakage.
- Clear formula is paintable and unobtrusive for finished projects.
Cons
- Requires a longer drying and curing time than many standard glues.
- Has a distinct odor during application; good ventilation is necessary.
- Can be difficult to remove once fully cured.
- Tube packaging may require careful handling to prevent clogs.
Setup, Compatibility & Care
Setup:
- Ensure both surfaces to be bonded are clean, dry, and free from dust, oil, or grease.
- For plastics, it's recommended to test adhesion on an inconspicuous area first.
- Apply E6000 Premium directly to one surface. For smoother materials, applying to both surfaces and allowing to set for a few minutes before joining can improve bond strength.
- Press the surfaces together firmly and allow them to cure.
Compatibility:
- Bonds Well: Most plastics (polycarbonate, PVC, ABS, acrylics, polystyrene), wood, metal, fabric, ceramic, glass, cement, clay, rubber, and fiberglass.
- Test First: Always test on a small, hidden area for unknown materials or painted surfaces.
- Not Recommended For: Styrofoam® or polystyrene foam, polyethylene, or polypropylene plastics.
Care:
- Store the tube in a cool, dry place away from direct sunlight.
- After use, clean the nozzle tip to prevent clogging. You can use a small amount of mineral spirits or denatured alcohol on a cloth to wipe the tip, then replace the cap securely.
- Avoid prolonged exposure to extreme temperatures during storage.