Suction Spray Gun - 2.0mm Nozzle Set
Not Available
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later or explore other options below.
Product Information
Full details
The FAST MOVER Suction Spray Gun with a 2.0mm nozzle is designed for professionals and DIY enthusiasts needing to paint large areas efficiently with solvent-based paints and primers. Its key benefit is the large 1000ml pot capacity, reducing refill frequency for continuous work. A primary caveat is its unsuitability for water-based paints. This conventional suction gun offers a tough, durable build and excellent performance for general-purpose spraying.
All features
| Brand | FAST MOVER |
|---|
Extended Product Information
FAQs
What is the main advantage of the 1000ml pot?
The 1000ml pot significantly increases the painting time between refills, making it highly efficient for covering large surfaces without frequent interruptions.
Can I use this spray gun with water-based paints?
No, this specific model is designed and recommended for solvent-based paints and primers only. It is not suitable for water-based applications.
What type of air compressor is needed?
You will need an air compressor capable of providing sufficient CFM (Cubic Feet per Minute) and PSI (Pounds per Square Inch) to operate the spray gun effectively. Consult your compressor's manual for specific recommendations.
How do I clean the spray gun after use?
After use, immediately clean all parts (needle, nozzle, air cap) with the appropriate solvent recommended for your paint. Flush the system thoroughly. Refer to the 'Care & Maintenance' section for detailed steps.
What other nozzle sizes are available?
This model is part of a range that also includes 1.3mm, 1.4mm, 1.6mm, 1.7mm, and 2.5mm nozzle set ups, catering to different viscosity paints and finish requirements.
Is the steel pot durable?
Yes, the spray gun features a tough and durable steel construction, including the 1000ml pot, designed to withstand regular use in demanding environments.
Troubleshooting
Uneven spray pattern or splattering
Check for blockages in the nozzle or air cap. Ensure the paint is properly thinned for spraying. Verify correct air pressure settings. Clean the fluid needle and ensure it moves freely.
Paint not flowing or flowing intermittently
Ensure the pot is correctly attached and sealed. Check that the fluid pickup tube is submerged in paint. Verify the fluid needle is opening correctly. Thin the paint if it's too thick.
Leaking from air cap or connections
Tighten the air cap. Check and tighten all air and fluid connections. Inspect seals for damage and replace if necessary.
Gun spitting (large drops of paint released suddenly)
This can indicate a blockage or insufficient atomization air. Clean the air cap and nozzle. Increase atomization air pressure slightly if possible. Ensure the fluid needle is retracting fully.
Pros and Cons
Pros
- Large 1000ml pot capacity for extended use
- Durable steel construction for longevity
- Suitable for a wide range of solvent-based paints and primers
- Provides excellent performance for general-purpose spraying
- Available in multiple nozzle sizes for specific tasks
Cons
- Not suitable for water-based paints
- Requires an air compressor (not included)
- Suction feed can sometimes be less consistent than gravity feed for very fine finishes
- Primarily designed for larger areas, may be cumbersome for very small touch-ups
Setup, Compatibility & Care
Setup:
- Ensure you have a compatible air compressor that can supply adequate airflow and pressure for the spray gun.
- Connect the air hose securely to the air inlet on the spray gun and the compressor.
- Attach the 1000ml steel pot to the bottom of the spray gun, ensuring a tight seal.
- Fill the pot with your chosen *solvent-based* paint or primer, ensuring it does not exceed the maximum fill line.
- Adjust the air regulator on your compressor to the recommended operating pressure for the spray gun (refer to compressor manual).
Compatibility:
- Paint Type: Primarily designed for solvent-based paints, primers, lacquers, and similar coatings.
- NOT compatible with water-based paints.
- Requires an air compressor (sold separately).
Care & Maintenance:
- After Each Use: Thoroughly clean the spray gun and pot to prevent paint from drying and clogging the system. Disassemble the fluid needle, nozzle, and air cap. Use appropriate solvent (as recommended for your paint) to clean all parts. Pay special attention to the nozzle tip and air cap.
- Storage: Store the cleaned spray gun in a dry, protected area. Ensure all components are dry before reassembly or storage to prevent rust.
- Regular Inspection: Periodically check seals and hoses for wear and tear.