Q.Max Sheet Metal Punch - 25mm
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later or explore other options below.
Product Information
Full details
The Q.Max Sheet Metal Punch (25mm) is designed for tradespeople and DIY enthusiasts needing to create clean, precise metric holes in sheet metal up to 16 gauge. Its key benefit is producing burr-free holes that require no secondary finishing, saving time and effort. A caveat is that the punch is sold separately from its required hexagonal key, which must be ordered to operate the tool.
All features
| Brand | Q.Max |
|---|
Extended Product Information
FAQs
What is the maximum thickness of sheet metal this punch can cut?
This punch is designed for sheet metal up to 16 gauge (approximately 1.5mm).
Do I need to buy anything else to use the punch?
Yes, you will need to purchase the corresponding hexagonal key (8mm for the 25mm punch) and the die separately.
Does the punch require sharpening?
The cutting edges are heat-treated for durability, but like all cutting tools, they may eventually require sharpening or replacement after significant use.
How do I ensure a burr-free hole?
The special design of the punch is intended to create burr-free holes. Ensure the tool is properly set up and the metal is within the specified thickness limit for best results.
What does 'sold singly without key' mean?
It means that the punch tool itself is sold as a single unit, but the essential accessory, the hexagonal key required to operate it, is not included and must be ordered separately.
Can I use this punch on materials other than sheet metal?
This tool is specifically designed for cutting clean holes in sheet metal up to 16 gauge. It is not intended for use on thicker materials, plastic, or wood.
How do I prevent the punch from rusting?
After use, clean the punch and store it in a dry place. A light application of oil on the metal parts can also help prevent rust due to its anti-corrosive surface finish.
Troubleshooting
Punch does not cut cleanly
Ensure the sheet metal is within the 16-gauge limit. Check for damage to the cutting edges of the punch and die. Lubricate the screw threads.
Tool is difficult to turn
Verify that the die nut is properly seated against the metal. Ensure the punch and screw threads are clean and lightly lubricated. Confirm you are using the correct size hexagonal key.
Punch gets stuck in the metal
This can occur if the metal is too thick or if the cutting edges are dull. Try backing the screw out slightly and re-engaging to complete the cut. For recurring issues, the punch may need sharpening or replacement.
Punch does not start the cut
Make sure the punch is correctly threaded onto the screw and that the die is properly positioned. Ensure the screw tip is centered on the intended punch location.
Pros and Cons
Pros
- Produces exceptionally clean, burr-free holes.
- Saves time by eliminating the need for deburring.
- Durable construction with heat-treated cutting edges.
- Corrosion-resistant finish for extended tool life.
- Efficient cutting with even load distribution.
Cons
- Hexagonal key must be purchased separately.
- Limited to sheet metal up to 16 gauge.
- Instructions may vary slightly for sizes above 15mm.
- Requires a separate die, sold individually.
Setup, Compatibility & Care
Setup:
- Ensure you have the correct Q.Max hexagonal key (MB, 8mm hexagonal wrench for the 25mm punch).
- Thread the punch onto the hexagonal screw.
- Pass the hexagonal screw through the desired hole location on the sheet metal.
- Position the die on top of the die nut (if applicable for this size).
- Screw the die nut onto the projecting hexagonal screw until it contacts the sheet metal.
- Use the hexagonal key to turn the hexagonal screw. The screw will pull the punch through the metal, creating the hole.
Compatibility:
- Designed for sheet metal up to 16 gauge (approximately 1.5mm thickness).
- Requires a separate Q.Max hexagonal key (8mm) and die for operation.
- This specific model is for 25mm hole size.
Care:
- Clean the punch and die after each use to remove metal debris.
- Wipe with a dry cloth and store in a dry environment to prevent rust.
- Periodically check the cutting edges for wear or damage.
- Apply a light lubricant to the threads to ensure smooth operation.