Bond It Glue Mix 2 Part Epoxy Adhesive - 2x 14g
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later or explore other options below.
Product Information
Full details
This Bond It Glue Mix is a 2-part epoxy adhesive designed for DIY enthusiasts and general-purpose bonding needs. Its key benefit is rapid curing, providing a strong and durable bond quickly. A potential caveat is its suitability primarily for general-purpose applications, which may not suit highly specialized material bonding. The product comes in a convenient 2x 14g pack, offering a multi-purpose resin adhesive for various projects.
All features
| Brand | Bond it |
|---|
Extended Product Information
FAQs
What is the working time after mixing the two parts?
The working time is typically short, often around 5 minutes, depending on the temperature. It's important to mix only what you can use within this timeframe.
How long does it take to fully cure?
Full cure is usually achieved within a few hours, but handling strength is often reached in minutes. Refer to the product packaging for specific times as they can vary.
Can I use this on flexible materials?
While it creates a strong bond, it is a rigid epoxy. It is best suited for rigid materials and may crack if the bonded item is subjected to significant flexing.
How should I store the unused adhesive?
Store in a cool, dry place, away from direct sunlight, with the caps tightly sealed. Ensure the original packaging is intact.
Is this adhesive waterproof once cured?
Once fully cured, the Bond It Glue Mix provides a water-resistant bond, suitable for many applications exposed to moisture, though prolonged immersion may degrade the bond over time.
What is the shelf life of the product?
The shelf life is typically 1-2 years when stored correctly. Check the packaging for an expiry date. Ensure both components are used before this date for optimal performance.
Can this adhesive be painted or sanded?
Yes, once fully cured, the bonded area can often be sanded to smooth the join and can be painted over with most types of paint.
Troubleshooting
Adhesive not curing or curing slowly
Ensure equal parts of resin and hardener were used and mixed thoroughly. Check for proper storage conditions and ensure the product is within its shelf life. Environmental temperature may also affect cure speed.
Weak bond strength
Verify that surfaces were properly prepared (clean, dry, free of contaminants). Ensure adequate mixing and correct application time. The bond may not have been fully cured before stress was applied.
Difficulty dispensing equal amounts
Gently squeeze tubes to avoid excessive pressure. If one component is significantly harder to dispense, it might be partially blocked or nearing the end of its usability.
Adhesive is too thick to spread
Ensure the product is stored at room temperature before mixing, as cold can increase viscosity. Mix thoroughly; sometimes this action can help. If very cold, allow tubes to warm up slightly.
Pros and Cons
Pros
- Fast curing time speeds up projects.
- Creates a strong and lasting bond.
- Versatile for many common materials.
- Supplied in convenient, separate tubes to maintain product integrity.
Cons
- Best suited for general-purpose bonding, not highly specialized applications.
- Requires precise mixing of the two components for optimal results.
- Curing time may vary slightly with temperature and humidity.
- May not be suitable for materials requiring extreme flexibility after curing.
Setup, Compatibility & Care
Setup:
- Ensure both surfaces to be bonded are clean, dry, and free from grease or dust.
- Carefully dispense equal amounts of the resin and hardener onto a clean, disposable surface.
- Thoroughly mix the two components until a uniform color is achieved. This typically takes about 60 seconds.
- Apply the mixed adhesive to one or both surfaces.
- Join the surfaces firmly and hold them in place for the initial set time (check packaging for specific times).
Compatibility:
This epoxy adhesive is generally compatible with wood, metal, most plastics, ceramics, glass, and concrete. It is not recommended for certain plastics like polyethylene or polypropylene, nor for use on fabrics or porous surfaces where absorption is high.
Care:
- Store the unused adhesive in its original packaging in a cool, dry place.
- Keep the caps tightly sealed when not in use.
- Clean up any uncured adhesive residue immediately with a suitable solvent (check product documentation for recommendations) or a damp cloth.
- Once cured, the adhesive is generally inert and can be cleaned with mild soap and water.