Craft Resin Crystal Clear Deep Pour Epoxy Resin Kit - 1.5L
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later or explore other options below.
Product Information
Full details
This Craft Resin Deep Pour Epoxy Resin Kit is designed for artists and crafters looking to create flawless, thick pours up to 2 inches in a single layer. Its key benefit is a bubble-free, non-yellowing, glass-like finish that cures quickly. A potential caveat is the need for careful temperature management during curing to achieve optimal results.
All features
| Brand | Craft Resin |
|---|
Extended Product Information
FAQs
What is the working time for this epoxy resin?
The working time is approximately 45-60 minutes, allowing ample time for mixing, coloring, and pouring, especially for larger projects.
Can I use this resin for very thin pours?
While designed for deep pours, it can be used for thinner layers, but its self-leveling and bubble-release properties are most beneficial in thicker applications.
Is the hardener included in the 1.5L kit?
Yes, the 1.5L kit includes 1L of clear resin and 0.5L of hardener, following the 2:1 ratio.
How long does it take to fully cure?
The resin cures to a hard, scratch-resistant state in approximately 48 hours. Full hardness and optimal strength may take 3-7 days depending on conditions.
Can I mix different colors into the resin?
Yes, you can use epoxy resin-specific pigments, mica powders, and dyes. Add them after mixing the resin and hardener, and mix thoroughly.
What is the maximum thickness for a single pour?
This deep pour formula is designed for single-layer pours of up to 2 inches thick.
How should I store the unused resin and hardener?
Store in their original, tightly sealed containers in a cool, dry place away from direct sunlight. Ensure the caps are securely fastened to prevent moisture absorption and degradation.
Troubleshooting
Sticky or uncured resin
Ensure the 2:1 ratio was strictly followed, and the resin was mixed thoroughly for the recommended time. Check room temperature; it should be between 70-77°F (21-25°C). Curing may take longer in cooler temperatures.
Excessive bubbles
The upgraded formula releases bubbles well, but ensure resin is slightly warm before mixing (e.g., place bottles in warm water). Mix slowly and deliberately to avoid introducing new air. Allow mixed resin to sit for a few minutes before pouring; this helps bubbles rise.
Surface imperfections or haziness
Ensure surfaces are clean and free of dust before pouring. Avoid disturbing the resin while it cures. For minor surface issues after curing, light sanding and applying a thin flood coat may resolve it.
Yellowing over time
While formulated to be non-yellowing, prolonged exposure to direct UV light can accelerate yellowing. Apply a UV-resistant top coat or keep finished pieces out of direct sunlight.
Pros and Cons
Pros
- Enables thick, single-layer pours up to 2 inches.
- Self-leveling and bubble-releasing properties simplify the process.
- Provides a durable, crystal-clear, and non-yellowing finish.
- Food-safe and low-odor for a safer crafting experience.
- Cures quickly to a heat-resistant and scratch-resistant surface.
- Comes as a complete kit with necessary accessories.
Cons
- Requires careful temperature control during curing for optimal results.
- Longer working time might be a consideration for very fast-paced projects.
- Not suitable for applications requiring extreme flexibility.
- Achieving a perfect finish requires proper preparation and mixing technique.
Setup, Compatibility & Care
Setup: The kit includes resin, hardener, mixing stick, pumps, gloves, and a manual. Ensure you work in a well-ventilated area, at a temperature between 70-77°F (21-25°C) for optimal curing. Measure the resin and hardener accurately using the 2:1 ratio (2 parts resin to 1 part hardener) by volume. Mix thoroughly for 3-5 minutes, scraping the sides and bottom of the container. Pour into your mold or project surface.
Compatibility: This epoxy resin is compatible with most mold materials, including silicone, plastic, and metal. It adheres well to various surfaces like wood, concrete, and most plastics. It can be used with pigments, mica powders, and other resin art additives.
Care: To maintain the glossy finish, clean surfaces with a soft, damp cloth. Avoid abrasive cleaners or solvents. For longevity, keep projects out of direct prolonged sunlight, which can cause yellowing over extended periods, and avoid exposing to temperatures exceeding its heat resistance limit of 176°F.